Brother International BAS-311F-0 Instruction Manual - English - Page 70

Error Codes

Get Brother International BAS-311F-0 PDF manuals and user guides View all Brother International BAS-311F-0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

12. ERROR CODES 12. ERROR CODES DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high voltages are present can result in severe injury. If an operation problem occurs, a buzzer will sound and an error code will appear on the display screen; if a programmer is connected, an error message will appear on the screen. Code Cause E.10 Emergency stop switch was pressed. Remedy Turn the EMERGENCY STOP switch clockwise and then pull it forward to release it. Press the STEP BACK (RESET) switch on the operation panel. E.11 Emergency stop switch was pressed. Turn the EMERGENCY STOP switch clockwise and then pull it forward to release it. Press the STEP BACK (RESET) switch on the operation panel. You can start sewing again, press the STEP BACK switch once more. E.12 E.13 E.14 E.15 E.16 E.17 E.20 E.21 E.22 E.30 E.31 E.32 Emergency stop switch is activated or its Turn off power and check it. connection is not correct. Defective connection of model selection connector. Turn off power and check connector P26. Foot switch was depressed, or connection of foot Turn off power and check it. switch is defective. Start switch was depressed, or connection of start Turn off power and check it. switch is defective. Machine head was tilted back. Turn off power and tilt machine head back. Operation panel switch was depressed when power Turn off power and check it. was turned on. Motor malfunctions or synchronizer is not Turn off power and check machine, synchronizer connected correctly. connection, and connectors P12 P15 P16. Motor malfunctioned. Turn off power and check ground wire connection. Needle up stop position error. Turn pulley to align timing mark with that on belt cover. Data exceeds available sewing area due to resize Adjust resize ratio. ratio. Stitch length exceeds 12.7mm due to resize ratio. Adjust resize ratio. No end code in sewing data. Input end code, or change program No. BAS-311F-0, 311F-L, 326F-0 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
12. ERROR CODES
BAS-311F-0, 311F-L, 326F-0
63
12. ERROR CODES
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
before opening the face plate of the control box. Touching areas where high voltages are present can result in
severe injury.
If an operation problem occurs, a buzzer will sound and an error code will appear on the display screen;
if a programmer is connected, an error message will appear on the screen.
Code
Cause
Remedy
E.10
Emergency stop switch was pressed.
Turn the EMERGENCY STOP switch clockwise and
then pull it forward to release it. Press the STEP BACK
(RESET) switch on the operation panel.
E.11
Emergency stop switch was pressed.
Turn the EMERGENCY STOP switch clockwise and
then pull it forward to release it. Press the STEP BACK
(RESET) switch on the operation panel.
You can start sewing again, press the STEP BACK
switch once more.
E.12
Emergency
stop
switch
is
activated
or
its
connection is not correct.
Turn off power and check it.
E.13
Defective connection of model selection connector.
Turn off power and check connector P26.
E.14
Foot switch was depressed, or connection of foot
switch is defective.
Turn off power and check it.
E.15
Start switch was depressed, or connection of start
switch is defective.
Turn off power and check it.
E.16
Machine head was tilted back.
Turn off power and tilt machine head back.
E.17
Operation panel switch was depressed when power
was turned on.
Turn off power and check it.
E.20
Motor
malfunctions
or
synchronizer
is
not
connected correctly.
Turn off power and check machine, synchronizer
connection, and connectors P12 P15 P16.
E.21
Motor malfunctioned.
Turn off power and check ground wire connection.
E.22
Needle up stop position error.
Turn pulley to align timing mark with that on belt cover.
E.30
Data exceeds available sewing area due to resize
ratio.
Adjust resize ratio.
E.31
Stitch length exceeds 12.7mm due to resize ratio.
Adjust resize ratio.
E.32
No end code in sewing data.
Input end code, or change program No.