Brother International CV3550 Operation Manual - Page 15

Preparation Before Threading

Get Brother International CV3550 PDF manuals and user guides View all Brother International CV3550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

English Chapter 2 PREPARATION BEFORE THREADING Thread tree Raise the telescoping thread tree to its highest position. Make sure that the thread holders are in alignment above the spool pins as illustrated below. CAUTION Before using a thread spool, be sure to remove the spool cushion. Cover stitch model 1 3 2 Top cover stitch model 1 3 2 1 Thread holder on thread tree 2 Spool pin 3 Correct position Using the thread spool cap When using sewing thread spools, the thread spool cap should be used as illustrated below. Make sure that the spool notch is on the bottom. 1 1 Thread spool cap Before using loosely spun nylon thread, be sure to install the spool cushion. If the thread spool cap is not fully pushed down, the thread may become entangled on the spool pin or the needle may bend or break. Spool mat When using thread spools or loosely spun thread that easily slips off the spool, place this mat under the spool. This prevents the thread from becoming entangled on the spool pin. Using the spool mat 1. Remove the spool cushion, and then place the spool mat on the spool pin. 2. Place the thread spool (with the spool notch at the bottom) on the spool pin, and then place the thread spool cap on top and fully push it down. 2 3 4 1 1 Spool cushion 2 Thread spool cap 3 Spool support 4 Spool mat CAUTION If the thread spool cap is not fully pushed down against the thread spool, the thread may become entangled on the spool pin or the needle may bend or break. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
13
English
CHAPTER 2
PREPARATION BEFORE THREADING
Thread tree
Raise the telescoping thread tree to its highest
position. Make sure that the thread holders are
in alignment above the spool pins as illustrated
below.
Cover stitch model
2
3
1
Top cover stitch model
2
3
1
1
Thread holder on thread tree
2
Spool pin
3
Correct position
Using the thread
spool cap
When using sewing thread spools, the thread
spool cap should be used as illustrated below.
Make sure that the spool notch is on the bottom.
1
1
Thread spool cap
CAUTION
Before using a thread spool, be sure to remove the
spool cushion.
Before using loosely spun nylon thread, be sure to
install the spool cushion.
If the thread spool cap is not fully pushed down,
the thread may become entangled on the spool pin
or the needle may bend or break.
Spool mat
When using thread spools or loosely spun thread
that easily slips off the spool, place this mat under
the spool.
This prevents the thread from becoming entangled
on the spool pin.
Using the spool mat
1. Remove the spool cushion, and then place the
spool mat on the spool pin.
2. Place the thread spool (with the spool notch at
the bottom) on the spool pin, and then place the
thread spool cap on top and fully push it down.
1
3
2
4
1
Spool cushion
2
Thread spool cap
3
Spool support
4
Spool mat
CAUTION
If the thread spool cap is not fully pushed down
against the thread spool, the thread may become
entangled on the spool pin or the needle may bend
or break.