Brother International HL-1050 Users Manual - English - Page 29

Test Print Mode, Hex Dump Print - reset

Get Brother International HL-1050 PDF manuals and user guides View all Brother International HL-1050 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

USER'S GUIDE Lamp Lit Drum Alarm Ready Data Test Print Mode The printer has the following test print mode. Follow these steps: 1. Make sure that the top cover is closed. 2. Hold down the switch and turn on the power switch. Keep the switch depressed until the Drum lamp comes on. The Drum lamp lights to indicate that the printer is in the test print mode. 3. Press the switch again to execute the test print or hold down the switch to select another option and release the switch to execute the selected option. The test print mode varies depending upon the printer model as follows: Choice Test sample page Print Config & Print Fonts I Factory Reset Hex Dump Print Function The printer prints a test sample page. The printer returns to the ready status after printing. The printer prints the current configuration of the printer and a list of the internal fonts. The printer returns to the ready status after printing. (HL-1040/1050 only) The printer is restored to the factory setting and permanent fonts and macros are cleared. The printer returns to the ready status after printing. (HL-1040/1050 only) The printer can print data as hexadecimal values, so that you can check data errors and problems. To exit from this mode, you have to turn off the printer. (HL-1040/1050 only) 3-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
USER’S GUIDE
3-4
Test Print Mode
The printer has the following test print mode. Follow these steps:
1.
Make sure that the top cover is closed.
2.
Hold down the switch and turn on the
power
switch. Keep the
switch
depressed until the
Drum
lamp comes on.
The
Drum
lamp lights to indicate that the printer is in the test print
mode.
3.
Press the
switch
again to execute the test print or hold down the
switch
to select another option and release the
switch
to execute the
selected option.
The test print mode varies depending upon the printer model as
follows:
Lamp Lit
Choice
Function
Drum
Test sample page
The printer prints a test sample page.
The printer returns to the ready status after
printing.
Alarm
Print Config
& Print
Fonts I
The printer prints the current configuration of
the printer and a list of the internal fonts.
The printer returns to the ready status after
printing. (HL-1040/1050 only)
Ready
Factory Reset
The printer is restored to the factory setting and
permanent fonts and macros are cleared.
The printer returns to the ready status after
printing. (HL-1040/1050 only)
Data
Hex Dump Print
The printer can print data as hexadecimal values,
so that you can check data errors and problems.
To exit from this mode, you have to turn off the
printer. (HL-1040/1050 only)