Brother International HL-630M Users Manual - English - Page 33

Reset/Hex Dump Mode, Hex Dump Print

Get Brother International HL-630M PDF manuals and user guides View all Brother International HL-630M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

CHAPTER 3 CONTROL PANEL Reset/Hex Dump Mode The printer has a reset/hex dump mode where you can select and perform any of three resets or a hex dump print. Follow these steps: 1. Press the SELECT switch to turn the printer off-line. 2. Hold down the SELECT switch and press the FF/CONT switch. The printer enters the reset/hex dump mode. The ALARM lamp blinks to indicate that the first choice, User Reset 1, is selected. See the table below. 3. Press the FF/CONT switch to select another choice. Every time you press the switch, the blinking lamp changes to select a choice. See the table below. 4. Press the SELECT switch to perform the selected choice. Blinking Lamp Choice ALARM User Reset 1 READY User Reset 2 DATA Factory Reset MANUAL Hex Dump Print Function The printer is restored to the user default settings without clearing permanent fonts and macros. You can execute this by long-pushing the RESET switch. The printer is restored to the user default settings and permanent fonts and macros are cleared. The printer is restored to the factory settings and permanent fonts and macros are cleared. The printer can print data as hexadecimal values, so that you can check data errors and problems. To exit from this mode, you have to reset the printer. After resetting, the printer returns to the ready status.  Note User settings are the printer settings that you change with the remote printer console program. See the software setup guide for details. 3-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
CHAPTER 3 CONTROL PANEL
3–7
Reset/Hex Dump Mode
The printer has a reset/hex dump mode where you can select and perform
any of three resets or a hex dump print. Follow these steps:
1.
Press the SELECT switch to turn the printer off-line.
2.
Hold down the SELECT switch and press the FF/CONT switch.
The printer enters the reset/hex dump mode. The ALARM lamp
blinks to indicate that the first choice, User Reset 1, is selected. See
the table below.
3.
Press the FF/CONT switch to select another choice.
Every time you press the switch, the blinking lamp changes to select a
choice. See the table below.
4.
Press the SELECT switch to perform the selected choice.
Blinking Lamp
Choice
Function
ALARM
User Reset 1
The printer is restored to the
user default settings without
clearing permanent fonts and
macros. You can execute this
by long-pushing the RESET
switch.
READY
User Reset 2
The printer is restored to the
user default settings and
permanent fonts and macros
are cleared.
DATA
Factory Reset
The printer is restored to the
factory settings and
permanent fonts and macros
are cleared.
MANUAL
Hex Dump Print
The printer can print data as
hexadecimal values, so that
you can check data errors and
problems. To exit from this
mode, you have to reset the
printer.
After resetting, the printer returns to the ready status.
Note
User settings are the printer settings that you change with the remote
printer console program. See the software setup guide for details.