Brother International HL-641 Users Manual - English - Page 66

Setting up the Printer for Apple Macintosh Computers, Questions, Recommendation

Get Brother International HL-641 PDF manuals and user guides View all Brother International HL-641 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

USER'S GUIDE Questions I cannot print from my application software. How can I change the printer's default settings? Sometimes I get a Print Overrun error when printing certain documents from Windows. Sometimes I get the Memory Full message. How can I correct this? Recommendation • If you are using Windows 3.1, make sure the supplied printer driver is installed and selected with your application software. • If you are using Windows 3.0 or earlier, make sure that proper printer driver is installed and selected to match the printer emulation. • If you use the serial interface, make sure that the serial slide switch of the serial interface is in the correct position and the interface settings are correctly set up with the DIP switches. Exit to DOS and use the remote printer console program. • Set the TrueType mode to 'Print as graphics' from the PRINT menu in your application software. • Reduce the print resolution or reduce the complexity of your document and try again. • Set the TrueType mode to 'Print as graphics' from the PRINT menu in your application software. • Another solution is to purchase more memory. • Reduce the print resolution or reduce the complexity of your document and try again. Setting up the Printer for Apple Macintosh Computers Questions The printer does not print. Recommendation Check the following: • The printer is plugged in. • Paper is loaded. • No error conditions are active (any blinking lamps on printer.) • Printer is on-line. 6-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
USER’S GUIDE
6–10
Questions
Recommendation
I cannot print from my
application software.
•
If you are using Windows 3.1, make sure
the supplied printer driver is installed and
selected with your application software.
•
If you are using Windows 3.0 or earlier,
make sure that proper printer driver is
installed and selected to match the printer
emulation.
•
If you use the serial interface, make sure
that the serial slide switch of the serial
interface is in the correct position and the
interface settings are correctly set up with
the DIP switches.
How can I change the
printer’s default settings?
Exit to DOS and use the remote printer console
program.
Sometimes I get a Print
Overrun error when
printing certain
documents from
Windows.
•
Set the TrueType mode to ‘Print as
graphics’ from the PRINT menu in your
application software.
•
Reduce the print resolution or reduce the
complexity of your document and try
again.
Sometimes I get the
Memory Full message.
How can I correct this?
•
Set the TrueType mode to ‘Print as
graphics’ from the PRINT menu in your
application software.
•
Another solution is to purchase more
memory.
•
Reduce the print resolution or reduce the
complexity of your document and try
again.
Setting up the Printer for Apple Macintosh Computers
Questions
Recommendation
The printer does not
print.
Check the following:
•
The printer is plugged in.
•
Paper is loaded.
•
No error conditions are active (any blinking
lamps on printer.)
•
Printer is on-line.