Brother International Innov-is BP2150L Operation Manual - Page 170
Troubleshooting
View all Brother International Innov-is BP2150L manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 170 highlights
TROUBLESHOOTING Problem Cause Solution Bobbin thread does The thread is not passed through the bobbin not wind neatly on the winding thread guide correctly. bobbin. Bobbin spins slowly. Correctly pass the thread through the bobbin winding thread guide. Press [+] in the bobbin winding window to increase the bobbin winding speed. The thread that was pulled out was not wound Wind the thread that was pulled off around onto the bobbin correctly. the bobbin 5 or 6 times clockwise. Skipped stitches Needle is turned, bent or the point is dull. Replace the needle. Using improper needle or thread for the selected fabric. Check the information about the needle and thread to be used. Machine is threaded incorrectly. Check the steps for threading the machine and rethread it correctly. Dust or lint has collected under the needle plate. Remove the dust or lint with the brush. Needle is installed incorrectly. Reinstall the needle correctly. Needle is defective. Replace the needle. Needle breaks Needle is installed incorrectly. Reinstall the needle correctly. Needle clamp screw is not tightened. Tighten the needle clamp screw. Needle is turned or bent. Replace the needle. Using improper needle or thread for the selected fabric. Check the needle and fabric combination. Upper thread tension is too strong. Adjust the thread tension setting. Fabric is pulled during sewing. Do not pull the fabric during sewing. Spool cap is set incorrectly. Check the method for attaching the spool cap, then reattach the spool cap. There are scratches around the hole(s) in the Replace the embroidery foot, or consult your embroidery foot. authorized dealer. There are scratches on the bobbin case. Replace the bobbin case, or consult your authorized dealer. Needle is defective. Replace the needle. Upper threading is incorrect. Check the steps for threading the machine and rethread the machine. Bobbin is set incorrectly. Reset the bobbin thread correctly. Embroidery foot is attached incorrectly. Attach the embroidery foot correctly. Screw of the embroidery foot is loose. Securely tighten the screw of the embroidery foot. Stabilizer is not attached to fabric being embroidered. Attach stabilizer. Bobbin thread is incorrectly wound. Use a correctly wound bobbin. Fabric does not feed Needle is turned, bent or the point is dull. through the machine Thread is entangled. Replace the needle. Cut the entangled thread and remove it from the race. Fabric puckers There is a mistake in the upper or bobbin threading. Check the steps for threading the machine and rethread it correctly. Thread tension is set incorrectly. Adjust the thread tension. Needle is turned, bent or the point is dull. Replace the needle. Spool cap is set incorrectly. Check the method for attaching the spool cap, then reattach the spool cap. High-pitched sound Pieces of thread are caught in the race. while sewing Upper threading is incorrect. Clean the race. Check the steps for threading the machine and rethread the machine. There are scratches on the bobbin case. Replace the bobbin case, or consult your authorized dealer. A bobbin designed specifically for this machine Incorrect bobbins will not work properly. Only is not used. use a bobbin designed specifically for this machine. Character pattern does not turn out Thread tension is set incorrectly. Adjust the thread tension. Page B-32 B-34 B-33 B-45 B-46, E-21 B-38 A-15 B-45 B-45 B-45 B-45 B-45 B-46, E-21 E-30 - B-38 B-42 A-15 B-45 B-38 B-36 B-42 B-42 E-11 B-31 B-45 A-13 B-36, B-38 E-30 B-45 B-38 A-15 B-38 A-15 B-36 E-30 A-20