Brother International Innov-is XP1 Operation manual Sewing - Page 214

After sewing

Get Brother International Innov-is XP1 PDF manuals and user guides View all Brother International Innov-is XP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 214 highlights

TROUBLESHOOTING ■ After sewing Problem Thread tension is incorrect. Character or decorative stitch patterns are misaligned. Stitch pattern does not turn out. Cause Upper threading is incorrect. Bobbin is set incorrectly. Using improper needle or thread for the selected fabric. Presser foot holder is not attached correctly. Thread tension is set incorrectly. Bobbin thread is incorrectly wound. Needle is turned, bent or the point is dull. A bobbin designed specifically for this machine is not used. Stitch pattern adjustment settings were set incorrectly. Solution Check the steps for threading the machine and rethread the machine. Reset the bobbin. (If needle plate was removed, reinstall needle plate and tighten screws prior to installing bobbin case.) Check the "Fabric/Thread/Needle Combinations" chart. Reattach the presser foot holder correctly. Adjust the thread tension. Use a correctly wound bobbin. Replace the needle. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. Revise the stitch pattern adjustment settings. Wrong presser foot was used. Attach the correct presser foot. Did not use a stabilizer material on thin fabrics Attach a stabilizer material. or stretch fabrics. Thread tension is set incorrectly. Adjust the thread tension. Fabric was pulled, pushed or fed at an angle Sew while guiding the fabric with your hands while it was being sewn. so that the fabric is fed in a straight line. The thread is tangled, for example, in the bobbin case. Remove the tangle thread. If the thread is tangled in the bobbin case, clean the race. Page 61 58 71 - 87 52 69 58 164 218 163 87 77 198 CAUTION • This machine is equipped with a thread detection device. If the "Start/Stop" button is pushed before the upper threading is done, the machine will not operate properly. • If the power is disconnected during sewing: Turn the main power to OFF and unplug the machine. If you restart the machine, follow the Operation Manual for operating the machine correctly. 212

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
TROUBLESHOOTING
212
■
After sewing
Problem
Cause
Solution
Page
Thread tension is
incorrect.
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
61
Bobbin is set incorrectly.
Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
58
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
71
Presser foot holder is not attached correctly.
Reattach the presser foot holder correctly.
—
Thread tension is set incorrectly.
Adjust the thread tension.
87
Bobbin thread is incorrectly wound.
Use a correctly wound bobbin.
52
Needle is turned, bent or the point is dull.
Replace the needle.
69
A bobbin designed specifically for this
machine is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
58
Character or
decorative stitch
patterns are
misaligned.
Stitch pattern adjustment settings were set
incorrectly.
Revise the stitch pattern adjustment settings.
164
Stitch pattern does
not turn out.
Wrong presser foot was used.
Attach the correct presser foot.
218
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material.
163
Thread tension is set incorrectly.
Adjust the thread tension.
87
Fabric was pulled, pushed or fed at an angle
while it was being sewn.
Sew while guiding the fabric with your hands
so that the fabric is fed in a straight line.
77
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
198
CAUTION
•
This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the
upper threading is done, the machine will not operate properly.
•
If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the Operation Manual for operating the machine correctly.