Brother International RH-9800 Instruction Manual - English - Page 34
Knife operation BEFORE/OFF/AFTER setting, ON: Enabled Determined by timer
View all Brother International RH-9800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 34 highlights
6. USING THE OPERATION PANEL AND FRONT PANEL No. Contents Setting range 07 Y direction offset for return seam to prevent OFF: No offset thread breakage ON: Offset by 1/2 pitch 08 Sewing end pitch for buttonhole taper to OFF: No change prevent fraying ON: Change No. of stitches before pitch change for memory 09 switch No. 08 01: 1 stitch, 02: 2 stitches, 03: 3 stitches, * Does not appear when memory switch No. 08 04: 4 stitches, 05: 5 stitches is set to OFF. 10 No. of stitches after pitch change for memory switch No. 08 * Does not appear when memory switch No. 08 is set to OFF. 01: 1 stitch, 02: 2 stitches, 03: 3 stitches, 04: 4 stitches, 05: 5 stitches, 06: 6 stitches, 07: 7 stitches, 08: 8 stitches, 09: 9 stitches 11 Test feeding speed OFF: Standard speed ON: Low speed Speed for memory switch No. 11 20: 20% of standard speed 12 * Does not appear when memory switch No. 11 35: 35% of standard speed is set to OFF. 50: 50% of standard speed 13 Knife operation (BEFORE/OFF/AFTER) setting OFF: Setting not possible within cycle program ON: Setting possible within cycle program 14 Special lapel cutting device OFF: Disabled ON: Enabled 15 Button hole sensor (Special lapel cutting OFF: Disabled device) ON: Enabled Timer for checking lowering of cutting block OFF:Disabled (Determined from slit signal 16 (Timer for determining if cutting block is stopping) lowered) ON: Enabled (Determined by timer) 17 Time for memory switch No. 16 * Does not appear when memory switch No. 16 is set to OFF. 42: 420 ms, 45: 450ms, 48: 480ms, 51: 510ms, 54: 540 ms 18 Changing cutting block ON time * Disabled (always "OFF") when switch No. 16 is "ON" memory OFF: Disabled (25 ms) ON: Enabled 19 Time for memory switch No. 18 * Does not appear when memory switch No. 18 is set to OFF. 05: 50 ms, 10: 100ms, 15: 150ms, 20: 200 ms 20 Timer for checking raising of cutting block (Timer for determining if the cutting block has been raised to a position where it will not touch the next feed bracket to operate) OFF: Disabled (Determined from number of slit signals) ON: Enabled (Determined by timer) Time for memory switch No. 20 15: 150ms, 20: 200 ms, 25: 250ms, 21 * Does not appear when memory switch No. 20 30: 300ms, 35: 350ms, 40: 400ms, is set to OFF. 45: 450ms, 50: 500ms Cutting block raising check timer (Raised position of the cutting block is 22 determined from the number of slit signals, and OFF: Disabled timer is updated) ON: Enabled * Disabled (always "OFF") when memory switch No. 20 is "ON" Time for memory switch No. 22 05: 50 ms, 10: 100ms, 15: 150ms, 23 * Does not appear when memory switch No. 22 20: 200 ms, 25: 250ms, 30: 300ms, is set to OFF. 35: 350ms, 40: 400ms 24 Setting tacking length to 0 for straight tacking OFF: Disabled specifications ON: Enabled 25 Spare - 99 Initial value OFF OFF 01 01 OFF 50 OFF OFF OFF OFF 45 OFF 05 OFF 20 OFF 05 OFF - RH-9800 28