Brother International RH-9800 Instruction Manual - English - Page 35

List of error codes, Codes E-60 to E-89

Get Brother International RH-9800 PDF manuals and user guides View all Brother International RH-9800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

6. USING THE OPERATION PANEL AND FRONT PANEL 6-7. List of error codes If the buzzer sounds and an error code starting with "E" appears in the front panel display, check according to the table below. Codes E-00 to E-16 are errors which are displayed when the power is turned on. Codes E-30 to E-59 are resetting errors which are displayed before operation and after the EMERGENCY STOP switch is pressed. Codes E-60 to E-89 represent errors which occur during operation. Code E-00 E-02 E-03 E-04 E-05 E-09 E-10 E-12 E-15 E-16 E-30 E-32 E-35 E-40 E-42 E-45 E-46 E-50 E-51 E-52 E-59 E-60 E-62 E-69 E-70 E-71 E-72 E-75 E-76 E-80 E-81 E-82 E-89 E-91 Explanation Resetting method EMERGENCY STOP switch was pressed. Press the EMERGENCY STOP switch once more and then press the RESET button. Machine head is raised (safety switch is off). Turn off the power. Cloth presser switch was pressed. Start switch was pressed. Release the cloth presser switch and then press the RESET button. Release the start switch and then press the RESET button. RESET button was pressed. Turn off the power. Sewing specifications changeover harness and stitch changeover harness and PROM version do not match. length Turn off the power. Needle bar is not at the highest position. Raise the needle to the needle up position and then press the RESET button. Cutting block is lowered. Turn off the power. Lower thread and gimp trimming knife does not retract. Turn off the power. Upper thread trimming knife does not retract. Turn off the power. EMERGENCY STOP switch was pressed. Press the EMERGENCY STOP switch once more and then press the RESET button. Machine head is raised (safety switch is off). Turn off the power. RESET button was pressed. Needle bar has not been raised. Turn off the power and then press the RESET button. Raise the needle to the needle up position and then press the RESET button. Cutting block is lowered. Turn off the power. Lower thread and gimp trimming knife does not retract. Turn off the power. Upper thread trimming knife does not retract. Turn off the power. X axis is not at the home position. Turn off the power. Y axis is not at the home position. Turn off the power. θ axis is not at the home position Turn off the power. Sewing data has been corrupted (checked for each program). Turn off the power. EMERGENCY STOP switch was pressed. Press the RESET button (to interrupt) or the start switch (to continue). Machine head is raised (safety switch is off). Turn off the power. Needle bar does not stop at the highest position. Raise the needle to the needle up position and then press the start switch (to continue). Needle up signal does not turn on and off during operation. Turn off the power. Needle down signal does not turn on and off during operation. Turn off the power. Cutting block operation is incorrect. Turn off the power. Lower thread and trimming operations are incorrect. Turn off the power. Upper thread operation is incorrect. Turn off the power. When the feed bracket returns to the home position, the X axis is not at the home position. Turn off the power. When the feed bracket returns to the home position, the Y axis is not at the home position. Turn off the power. When the feed bracket returns not at the home position. to the home position, the θ axis is Turn off the power. Machine operation direction is reversed. Turn off the power. Pulse motor overcurrent Turn off the power. Note: Errors E-50, E-51 and E-52 are not errors to be reset after the EMERGENCY STOP switch is pressed. RH-9800 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
6. USING THE OPERATION PANEL AND FRONT PANEL
RH-9800
29
6-7. List of error codes
If the buzzer sounds and an error code starting with "E" appears in the front panel display, check according to
the table below.
Codes E-00 to E-16 are errors which are displayed when the power is turned on. Codes E-30 to E-59 are resetting errors
which are displayed before operation and after the EMERGENCY STOP switch is pressed.
Codes E-60 to E-89
represent errors which occur during operation.
Code
Explanation
Resetting method
E-00
EMERGENCY STOP switch was pressed.
Press the EMERGENCY STOP switch once
more and then press the RESET button.
E-02
Machine head is raised (safety switch is off).
Turn off the power.
E-03
Cloth presser switch was pressed.
Release the cloth presser switch and then
press the RESET button.
E-04
Start switch was pressed.
Release the start switch and then press
the RESET button.
E-05
RESET button was pressed.
Turn off the power.
E-09
Sewing specifications changeover harness and stitch length
changeover harness and PROM version do not match.
Turn off the power.
E-10
Needle bar is not at the highest position.
Raise the needle to the needle up position
and then press the RESET button.
E-12
Cutting block is lowered.
Turn off the power.
E-15
Lower thread and gimp trimming knife does not retract.
Turn off the power.
E-16
Upper thread trimming knife does not retract.
Turn off the power.
E-30
EMERGENCY STOP switch was pressed.
Press the EMERGENCY STOP switch once
more and then press the RESET button.
E-32
Machine head is raised (safety switch is off).
Turn off the power.
E-35
RESET button was pressed.
Turn off the power and then press the
RESET button.
E-40
Needle bar has not been raised.
Raise the needle to the needle up position
and then press the RESET button.
E-42
Cutting block is lowered.
Turn off the power.
E-45
Lower thread and gimp trimming knife does not retract.
Turn off the power.
E-46
Upper thread trimming knife does not retract.
Turn off the power.
E-50
X axis is not at the home position.
Turn off the power.
E-51
Y axis is not at the home position.
Turn off the power.
E-52
θ
axis is not at the home position
Turn off the power.
E-59
Sewing data has been corrupted (checked for each program).
Turn off the power.
E-60
EMERGENCY STOP switch was pressed.
Press the RESET button (to interrupt) or
the start switch (to continue).
E-62
Machine head is raised (safety switch is off).
Turn off the power.
E-69
Needle bar does not stop at the highest position.
Raise the needle to the needle up position
and then press the start switch (to continue).
E-70
Needle up signal does not turn on and off during operation.
Turn off the power.
E-71
Needle down signal does not turn on and off during operation.
Turn off the power.
E-72
Cutting block operation is incorrect.
Turn off the power.
E-75
Lower thread and trimming operations are incorrect.
Turn off the power.
E-76
Upper thread operation is incorrect.
Turn off the power.
E-80
When the feed bracket returns to the home position, the X axis is
not at the home position.
Turn off the power.
E-81
When the feed bracket returns to the home position, the Y axis is
not at the home position.
Turn off the power.
E-82
When the feed bracket returns to the home position, the
θ
axis is
not at the home position.
Turn off the power.
E-89
Machine operation direction is reversed.
Turn off the power.
E-91
Pulse motor overcurrent
Turn off the power.
Note:
Errors E-50, E-51 and E-52 are not errors to be reset after the EMERGENCY STOP switch is pressed.