Home » Brother International Manuals » Sewing Machines » Brother International RH-981A » Manual Viewer

Brother International RH-981A Instruction Manual - English - Page 46

Cycle Program Setting, Cycle program setting

Get Brother International RH-981A PDF manuals and user guides

View all Brother International RH-981A manuals

Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Chapter 7 OTHER FUNCTIONS Cycle Program Setting Cycle program setting Setting can be performed as for continuous execution of 8 programs at maximum. The example below exemplifies changing the cycle program from [01 (ON), 01 (ON), 05 (OFF)] to [01 (ON), 01 (ON), 01 (ON), 05 (OFF)]. 1. Press the [P] key to start the programmer. 2. Press the [MENU] key to display the menu screen. W0012Q 3. Select the icon with the [ ] key and press the [ENTER] key. W0017Q 4. Select the required cycle program with the [ ] key and press the [ENTER] key. W0114Q 5. Select any one of the program No. (01 - 09) with the [+/-] key. W0069Q 6. Select [05] with the [ ] key and change to [01] with the [+/-] key. Change the knife setting below from [0FF] to [ON] with the same operation. W0069Q W0070Q 7. Select [-] below [C4] with the [ ] key and change to [05] with the [+/-] key. Change the knife setting below from [ON] to [OFF] with the same operation. If the knife setting is kept to be ON and no setting is performed for the knife at the machine, the knife performs operation in sewing on the settings set at the programmer although settings at the machine are prior to those at the programmer. W0070Q W0071Q E-40 PD-9810

Section	Page
Cover1	1
FUNCTIONS	4
CONTENTS	5
Chapter 1 INTRODUCTION	7
Name of Parts and Function	8
Illustration on the Screen Shows	10
Menu screen	10
Program No. selection screen	11
Parameter setting screen	12
Screen Directory	13
Chapter 2 PREPARATION	15
Connecting the Programmer to the Machine	16
Power ON/OFF	17
Set the power to ON	17
Set the power to OFF	17
Putting the Programmer in Store	18
Chapter 3 EXAMPLE OF THE PROGRAM CHANGE PROCEDURE	19
Parameter Changing of the Program No. 5	20
Chapter 4 PARAMETER	23
Parameter Table	24
When the programmer is connected to the machine with the taper tack specifications	24
When the programmer is connected to the machine with the straight bar tack specifications	27
Parameter Selection	30
Selection with the [SHORT CUT] key	30
Selection with the [UP/DOWN/LEFT/RIGHT] key	30
Selection with the [+/-] key	30
Changing the Parameter	31
Chapter 5 PROGRAM READING AND WRITING	33
Program Reading from the Machine	34
Program Writing to the Machine	35
Program Reading from the File	36
Program Writing to the File	37
Chapter 6 HANDY FUNCTIONS	39
Auto Read/Write Setting	40
When the auto read/write setting is ON	40
When the auto read/write setting is OFF	40
When the [MENU] key and the [P] key are concurrently pressed	40
File Saving Function	41
Chapter 7 OTHER FUNCTIONS	43
Data saving to another machine	44
Saving area	44
Saving method	44
Cycle Program Setting	46
Cycle program setting	46
Display of the program Nos. for the machine at cycle program writing	48
Initializing the Program in the Work Area	49
Initializing all of the program	49
Initializing one of any programs	49
Initializing all of the program in the environment setting area and work area	50
Environment Setting	51
Language used	51
Setting numbers of the program to read and write	52
Enable/disable for auto read/write	52
Display/non-display of the check message	53
PROM version display	54
Comparing the Program	55
Comparing with the data in the machine	55
Comparing with the data in the programmer	56
Copying the program	57
PROM Exchange Procedures	58
Change to factory settings	61
Chapter 8 ERROR MESSAGE	63
List of Messages	64
Data version unmatch error	64
Received data error	64
Communication error	64
Data lost error	64