Campbell Scientific 107 107-L Temperature Probe - Page 7

Model 107 Temperature Probe

Get Campbell Scientific 107 PDF manuals and user guides View all Campbell Scientific 107 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Model 107 Temperature Probe 1. Introduction The 107 Temperature Probe uses a thermistor to measure temperature in air, soil, and water. It is compatible with all Edlog and CRBasic dataloggers except the CR200(X) and CR9000(X). See Section 6, Specifications, for a complete list of compatible dataloggers. 2. Cautionary Statements Santoprene® rubber, which composes the black outer jacket of the 107 cable, will support combustion in air. It is used because of its resistance to temperature extremes, moisture, and UV degradation. It is rated as slow burning when tested according to U.L. 94 H.B. and passes FMVSS302. However, local fire codes may preclude its use inside buildings. 3. Initial Inspection • Check the packaging and contents of the shipment. If damage occurred during transport, immediately file a claim with the carrier. Contact Campbell Scientific to facilitate repair or replacement. • Check model information against the shipping documents to ensure the expected products and the correct lengths of cable are received. Model numbers are found on each product. On cables and cabled items, the model number is usually found at the connection end of the cable. Report any shortages immediately to Campbell Scientific. 4. Quickstart Short Cut is an easy way to program your datalogger to measure the 107 probe and assign datalogger wiring terminals. Use the following procedure to get started. 1. Install Short Cut by clicking on the install file icon. Get the install file from either www.campbellsci.com, the ResourceDVD, or find it in installations of LoggerNet, PC200W, PC400, or RTDAQ software. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Model 107 Temperature Probe
1.
Introduction
The 107 Temperature Probe uses a thermistor to measure temperature in air,
soil, and water.
It is compatible with all Edlog and CRBasic dataloggers
except the CR200(X) and CR9000(X).
See Section 6,
Specifications
, for a
complete list of compatible dataloggers.
2.
Cautionary Statements
Santoprene
®
rubber, which composes the black outer jacket of the 107 cable,
will support combustion in air.
It is used because of its resistance to
temperature extremes, moisture, and UV degradation.
It is rated as slow
burning when tested according to U.L. 94 H.B. and passes FMVSS302.
However, local fire codes may preclude its use inside buildings.
3.
Initial Inspection
•
Check the packaging and contents of the shipment. If damage occurred
during transport, immediately file a claim with the carrier.
Contact
Campbell Scientific to facilitate repair or replacement.
•
Check model information against the shipping documents to ensure the
expected products and the correct lengths of cable are received.
Model
numbers are found on each product. On cables and cabled items, the
model number is usually found at the connection end of the cable. Report
any shortages immediately to Campbell Scientific.
4.
Quickstart
Short Cut
is an easy way to program your datalogger to measure the 107 probe
and assign datalogger wiring terminals.
Use the following procedure to get
started.
1.
Install
Short Cut
by clicking on the install file icon.
Get the install file
from either
www.campbellsci.com
, the ResourceDVD, or find it in
installations of
LoggerNet
,
PC200W
,
PC400
, or
RTDAQ
software.
1