Canon 1231B002 REALiS Manual - Page 27

Preparing the Remote Control

Get Canon 1231B002 - REALiS SX6 SXGA+ LCOS Projector PDF manuals and user guides
UPC - 013803065251
View all Canon 1231B002 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Preparing the Remote Control Installing Remote Control Batteries 1 2 Open the battery com- Insert batteries. 3 partment lid. Insert new two AAA-size Slide the lid with it batteries in the compart- pressed down. ment with the + and - poles positioned cor- rectly. Replace the compartment lid. BEFORE USE z You can check the batteries of the remote control by pressing the [LIGHT] button. If all buttons on the remote control do not light when the [LIGHT] button is pressed, or buttons are inoperative when you attempt to operate the projector, replace with new batteries. z It is recommended to check the batteries before a presentation. Remote Control Operating Range Point the remote control to the infrared remote receiver on the front or rear of the projector whenever pressing any button. z Use the remote control within a distance of approximately 5 m (16.4') from the projector. z Use the remote control within an angle of 30° in any direction from directly in front of the infrared remote receiver. 30° 5 m (16.4') 30° 5 m (16.4') 30° 30° The remote control may be inoperative if: z There is an obstacle between the remote control and main unit. z The infrared remote receiver on the main unit is exposed to direct sunlight or strong light of lighting equipment. z The remote control uses infrared light. z When you use two projectors at the same time, you can change the channel settings to pre- vent the two remote controls from interfering with each other (P111). 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
27
BEFORE USE
Preparing the Remote Control
Installing Remote Control Batteries
Remote Control Operating Range
Point the remote control to the infrared
remote receiver on the front or rear of the
projector whenever pressing any button.
Use the remote control within a distance
of approximately 5 m (16.4') from the pro-
jector.
Use the remote control within an angle of
30° in any direction from directly in front
of the infrared remote receiver.
You can check the batteries of the remote control by pressing the [LIGHT] button.
If all buttons on the remote control do not light when the [LIGHT] button is pressed, or but-
tons are inoperative when you attempt to operate the projector, replace with new batteries.
It is recommended to check the batteries before a presentation.
The remote control may be inoperative if:
There is an obstacle between the remote control and main unit.
The infrared remote receiver on the main unit is exposed to direct sunlight or strong light of
lighting equipment.
The remote control uses infrared light.
When you use two projectors at the same time, you can change the channel settings to pre-
vent the two remote controls from interfering with each other (P111).
1
Open the battery com-
partment lid.
Slide the lid with it
pressed down.
2
Insert batteries.
Insert new two AAA-size
batteries in the compart-
ment with the + and -
poles positioned cor-
rectly.
3
Replace the compart-
ment lid.
30°
30°
30°
30°
5 m
(16.4')
5 m
(16.4')