Canon CINE-SERVO 50-1000mm T5.0-8.9 EF User Manual - Page 43

How To Mount

Get Canon CINE-SERVO 50-1000mm T5.0-8.9 EF PDF manuals and user guides View all Canon CINE-SERVO 50-1000mm T5.0-8.9 EF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

2 HOW TO MOUNT 2 HOW TO MOUNT 2-1. MOUNT THE LENS ON THE CAMERA For PL mount, read the following instructions before mounting the lens. The PL mount supports /i communication, so make sure that the camera is set to "/i". Do not mount the lens if the camera is set to a mount communication mode other than /i. Doing so could result in malfunction. Before mounting the lens on the camera, make sure that the power of camera and the power of supply equipment are turned off. 1 Attach the lens to the camera tightly so that both mounting surfaces are in complete contact. The mounting method differs depending on the lens mounts. Refer to the operation manual for the respective camera for the detailed information. If the rod interferes with the lens body or drive unit when mounting the lens, remove the rod and then mount the lens. Attachment Holder Lens Support Screw supplied with the Lens Support 2 Secure the lens holder on the lens support using the screw supplied with the lens support. 3 Secure the attachment holder to a different lens 2 support from the lens support mentioned in step , and fit the attachment holder into the attachment holder contact plate (㉒ in figure on page 2) at the rear of the lens. 4 Fix the lens support to the rods using lens support fixing screws. Rods (Φ19) Lens Support Fixing Screws E3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
E3
1
Attach the lens to the camera tightly so that both
mounting surfaces are in complete contact.
The mounting method differs depending on the lens
mounts. Refer to the operation manual for the respective
camera for the detailed information.
If the rod interferes with the lens body or drive unit when
mounting the lens, remove the rod and then mount the
lens.
2
Secure the lens holder on the lens support using the
screw supplied with the lens support.
3
Secure the attachment holder to a different lens
support from the lens support mentioned in step
2
,
and fit the attachment holder into the attachment
holder contact plate (
㉒
in figure on page 2) at the
rear of the lens.
4
Fix the lens support to the rods using lens support
fixing screws.
2 HOW TO MOUNT
2-1. MOUNT THE LENS ON THE CAMERA
For PL mount, read the following instructions before mounting the lens.
The PL mount supports /i communication, so make sure that the camera is set to “/i”. Do not mount the lens if
the camera is set to a mount communication mode other than /i. Doing so could result in malfunction.
Before mounting the lens on the camera, make sure that the power of camera and the power of supply
equipment are turned off.
2 HOW TO MOUNT
Lens Support
Screw supplied with the
Lens Support
Attachment
Holder
Rods
(Φ19)
Lens Support Fixing Screws