Canon LE-5W BK User Manual - Page 92

The image does not display properly, Power shuts down, Execute the AUTO PC function.

Get Canon LE-5W BK PDF manuals and user guides View all Canon LE-5W BK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

The image does not display properly Cause The image shifts left or right with analog PC inputs. Also, the image flickers. The image is top/bottom reversed or left/right reversed. Remedy Execute the AUTO PC function. There is a problem with the ceiling mounting/rear projection feature setup. Using a computer cable in which some of the pins do not connect. Check the setting details for Setup > Advanced > Projector Position. (P63) Use the connector cable included with the projector. Power shuts down Cause The air intake vents or exhaust vents are blocked. For commercially available parts, use a computer cable in which all of the pins connect. Remedy If the air intake vents or exhaust vents are blocked, the temperature inside the projector will rise and the projector will automatically shut down for protection. (P20) Improper operating environment. After the temperature of the projector drops, and the air intake vents and exhaust vents are unblocked, turn it on again. Check that the operating environment is 0°C to 40°C. (P16) When the causes for the above cannot be found. When using the projector in a high altitude location between 1500 m to 3000 m, set it to the high altitude mode. (P62) Technical problems may occur so unplug the power cord. Contact your Canon Customer Support Center as soon as possible. (Back cover of this manual) Appendix 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Appendix
92
The image does not display properly
Power shuts down
Cause
Remedy
The image shifts left or right with
analog PC inputs. Also, the image
flickers.
Execute the AUTO PC function.
The image is top/bottom reversed or
left/right reversed.
There is a problem with the ceiling
mounting/rear projection feature setup.
Check the setting details for Setup >
Advanced > Projector Position. (
P63
)
Using a computer cable in which
some of the pins do not connect.
Use the connector cable included with the
projector.
For commercially available parts, use a
computer cable in which all of the pins
connect.
Cause
Remedy
The air intake vents or exhaust
vents are blocked.
If the air intake vents or exhaust vents are
blocked, the temperature inside the
projector will rise and the projector will
automatically shut down for protection.
(
P20
)
After the temperature of the projector
drops, and the air intake vents and exhaust
vents are unblocked, turn it on again.
Improper operating environment.
Check that the operating environment is
0°C to 40°C. (
P16
)
When using the projector in a high altitude
location between 1500 m to 3000 m, set it
to the high altitude mode. (
P62
)
When the causes for the above
cannot be found.
Technical problems may occur so unplug
the power cord. Contact your Canon
Customer Support Center as soon as
possible. (
Back cover
of this manual)