Canon LV-X7 LV User's Manual - Page 70

Appendix

Get Canon LV-X7 PDF manuals and user guides View all Canon LV-X7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

7. Appendix ❶ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. WARNING Indicator WARNING POWER POWER Indicator LAMP LAMP Indicator INPUT AUTO PC VOL - MENU KEYSTONE VOL + BACK Indicator Messages POWER Indicator Blinking light Steady light Indicator Condition Off Green Orange Green Orange 0.5 sec On, 0.5 sec Off 2.5 sec On, 0.5 sec Off 0.5 sec On, 0.5 sec Off Projector Condition The main power is off - The projector is getting ready Wait for a moment. to turn on. Off Timer is enabled. - T h e p r o j e c t o r i s c o o l i n g Wait for a moment. down. The projector is turned on. - The projector is in Standby. - Note WARNING Indicator Blinking light Steady light Indicator Condition Off Red Green Orange Projector Condition Note Normal - 1 c y c l e (0 . 5 s e c L a mp c ov er er r or or l a mp Replace the lamp cover or lamp housing correctly. On, 2.5 sec Off) housing error (→ page 60) 2 c y c l e (0 . 5 s e c Temperature error On, 0.5 sec Off) The projector is overheated. Move the projector to a cooler location. 4 c y c l e (0. 5 s e c Fan error On, 0.5 sec Off) Fans will not work correctly. 6 c y c l e (0. 5 s e c Lamp error On, 0.5 sec Off) Lamp fails to light. Wait a full minute and then turn on again. Re-firing the lamp (The pro- The projector is re-firing. jector is cooling down.) Wait for a moment. Key lock is on. You have pressed cabinet button when Key lock is on. (→ page 50) LAMP Indicator Blinking light Steady light Indicator Condition Off Red Red Green Projector Condition Normal - Lamp has reached its end of life. Lamp Replace the lamp. replacement message will be displayed. Lamp has been used beyond its limit. Replace the lamp. The projector will not turn on until the lamp is replaced. Lamp mode is set to Quiet mode. - Note If a temperature error occurs If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the WARNING indicator blinking (2-cycle On and Off.) Should this happen, do the following: - Unplug the power cord after the cooling fans stop. - Move the projector to a cooler location if the room where you are presenting is particularly too warm. - Clean the ventilation holes if they are clogged with dust. - Wait about 60 minutes until the inside of the projector becomes cool enough. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
6±
7. Appendix
❶
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
WARNING Indicator
LAMP Indicator
Indicator Messages
POWER Indicator
MENU
BACK
KEYSTONE
WARNING
P
O
W
E
R
AUTO PC
INPUT
VOL
-
VOL
+
LAMP
Warning iNDIcAToR
POWer iNDIcAToR
laMP iNDIcAToR
Indicator Condition
Projector Condition
Note
Off
The main power is off
–
Blinking light
Green
0.5 sec On,
0.5 sec Off
The projector is getting ready
to turn on.
Wait for a moment.
2.5 sec On,
0.5 sec Off
Off Timer is enabled.
–
Orange
0.5 sec On,
0.5 sec Off
The projector is cooling
down.
Wait for a moment.
Steady light
Green
The projector is turned on.
–
Orange
The projector is in Standby.
–
Indicator Condition
Projector Condition
Note
Off
Normal
–
Blinking light
Red
1 cycle (0.5 sec
On, 2.5 sec Off)
Lamp cover error or lamp
housing error
Replace the lamp cover or lamp housing correctly.
(
→
page
60
)
2 cycle (0.5 sec
On, 0.5 sec Off)
Temperature error
The projector is overheated. Move the projector to a
cooler location.
4 cycle (0.5 sec
On, 0.5 sec Off)
Fan error
Fans will not work correctly.
6 cycle (0.5 sec
On, 0.5 sec Off)
Lamp error
Lamp fails to light. Wait a full minute and then turn on
again.
Green
Re-firing the lamp (The pro-
jector is cooling down.)
The projector is re-firing.
Wait for a moment.
Steady light
Orange
Key lock is on.
You have pressed cabinet button when Key lock is on.
(
→
page
50
)
Indicator Condition
Projector Condition
Note
Off
Normal
–
Blinking light
Red
Lamp has reached its end of life. Lamp
replacement message will be displayed.
Replace the lamp.
Steady light
Red
Lamp has been used beyond its limit.
The projector will not turn on until the
lamp is replaced.
Replace the lamp.
Green
Lamp mode is set to Quiet mode.
–
If a temperature error occurs
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the
WARNING indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
- Unplug the power cord after the cooling fans stop.
- Move the projector to a cooler location if the room where you are presenting is particularly too warm.
- Clean the ventilation holes if they are clogged with dust.
- Wait about 60 minutes until the inside of the projector becomes cool enough.