Canon Optura Optura Instruction Manual - Page 9

Charging and attaching the battery pack - 50

Get Canon Optura PDF manuals and user guides View all Canon Optura manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Charging and attaching the battery pack 1 2 3 E 4 Mastering the Basics Your battery pack was partially charged before it left the factory. It should have enough power for you to check that your camera is working properly. However, you must charge the battery pack fully if you want it to power the camera for more than a few minutes. 1. Attach the battery pack to the power adapter. • Align the triangle on the battery pack with the line on the power adapter. • Make sure the DC coupler is not connected. 2. Plug the adapter into an AC outlet. • The charge indicator flashes red to show that charging is in progress. Single flashes mean that the battery pack is less than 50% charged. Double flashes mean that it is between 50% and 75% charged. Triple flashes mean that it is more than 75% charged. • The indicator glows steadily when the battery pack is fully charged. 3. Take the battery pack off the adapter and insert it into the camera. • First lift up the battery cover then insert the battery in the direction of the arrow, with the arrow facing down, until it clicks into place. 4. Remove the battery pack after use. • Press the BATTERY RELEASE knob to the left. • Always turn the camera off before removing the power source. Note: • You can find detailed notes for using the batteries in the "Notes on Using the Batteries" on p. 55. These notes include charging and recording times and how to install the back-up battery. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Mastering the Basics
9
E
Charging and attaching the battery pack
Your battery pack was partially charged before it left the factory. It should have
enough power for you to check that your camera is working properly. However,
you must charge the battery pack fully if you want it to power the camera for
more than a few minutes.
1.
Attach the battery pack to the power adapter.
•
Align the triangle on the battery pack with the line on the power adapter.
•
Make sure the DC coupler is not connected.
2.
Plug the adapter into an AC outlet.
•
The charge indicator flashes red to show that charging is in progress. Single
flashes mean that the battery pack is less than 50% charged. Double flashes
mean that it is between 50% and 75% charged. Triple flashes mean that it is
more than 75% charged.
•
The indicator glows steadily when the battery pack is fully charged.
3.
Take the battery pack off the adapter and insert it into the camera.
•
First lift up the battery cover then insert the battery in the direction of the
arrow, with the arrow facing down, until it clicks into place.
4.
Remove the battery pack after use.
•
Press the BATTERY RELEASE knob to the left.
•
Always turn the camera off before removing the power source.
Note:
•
You can find detailed notes for using the batteries in the “Notes on Using the
Batteries” on p. 55. These notes include charging and recording times and how
to install the back-up battery.
3
1
2
4