Home » Canon Manuals » Projectors » Canon REALiS LCOS WUX10 » Manual Viewer

Canon REALiS LCOS WUX10 REALiS WUX10 User Manual - Page 83

No Signal Screen, Screen When Blank, user's logo has been registered.

Get Canon REALiS LCOS WUX10 PDF manuals and user guides

View all Canon REALiS LCOS WUX10 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

No Signal Screen [User screen settings] - [No signal screen] HDMI DIGITAL PC ANALOG PC COMPONENT VIDEO Display settings User screen settings No signal screen You can display a user logo on a screen when there is no input signal. Setting Display Status Screen When Blank [User screen settings] - [Screen when blank] HDMI DIGITAL PC ANALOG PC COMPONENT VIDEO Display settings User screen settings Screen when blank You can display a user logo a screen when the projected image is blackened out temporarily by pressing the BLANK button on the remote control. Black Blue User logo The screen is all black. Displays no user logo. The screen is blue background. Displays no user logo. Displays a user logo. Black Blue User logo The screen is all black. Displays no user logo. The screen is blue background. Displays no user logo. Displays a user logo. Press the OK button to accept your setting and then press the MENU button. • [Blue] is the factory default. • [User logo] is available only when a user's logo has been registered. Press the OK button to accept your setting and then press the MENU button. • [Black] is the factory default. • [User logo] is available only when a user's logo has been registered. Setting Up Functions from Menus 83

Section	Page
To Start Menu	2
Quick Reference Guide	4
Table of Contents	5
Safety Instructions	10
Safety Precautions	11
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.	12
AC Power Cord Requirement	14
Federal Communication Commission Notice	15
Canadian Radio Interference Regulations	15
Precautions on Handling the Batteries in the Remote Controller	16
Lamp Handling Precautions	16
Carrying/Transporting the Projector	17
Installation Precautions	17
Before Use	19
Supplied Accessories	20
Installing the Lens Cap	20
Putting the Projector in the Carrying Bag	21
Part Names	22
Main Unit of Projector	22
Front Side	22
Rear Side	22
Bottom Side	23
Remote Control	24
Top Control	26
Input Terminals	27
Preparing the Remote Control	28
Installing Remote Control Batteries	28
Remote Control Operating Range	28
Projecting an Image	29
Steps for Setting Up the Projector and Projecting an Image	30
Setting Up the Projector	31
Placing in Front of the Screen	31
Placing on a Level Place	32
When Pointing the Projector Up	33
Connecting the Projector	34
Connectable Equipment and Input Terminals	34
Connecting the Projector to the Computer	35
Connecting to RGB Monitor Output Terminal (analog connection)	35
Connecting to DVI Monitor Output Terminal (digital connection)	36
Outputting Audio to Speakers	37
Connecting to AV Equipment	38
Connecting to Digital Video Output Terminal (digital connection)	38
Connecting to Analog Video Output Terminal (analog connection)	39
Outputting Audio to Speakers	41
Starting Projection	42
When the Language Selection Screen Appears	43
When the Password Input Screen Appears	44
When \	44
When Notebook Computer Screen Does Not Appear	44
Adjusting Image	44
Changing Notebook Computer Screen Output	44
Turning On External Monitor Output	44
Setting Up the Screen Automatically	45
Auto Setup	45
Performing the Auto Setup	46
Selecting an Input Signal (INPUT)	47
Types of Input Signals	47
Selecting an Input Signal	48
Adjusting Image	49
Setting the Display Resolution of the Computer	49
Windows Vista	49
Windows XP	49
Macintosh OSX	49
AUTO PC	50
Performing the Auto PC Function	50
Adjusting the Image Size	51
Adjusting the Focus	52
Auto focusing	52
Manual focusing	52
Adjusting Keystone Distortion	53
Auto adjustment	53
Manual adjustment	53
Resetting the Keystone Adjustment	54
Selecting Screen Aspect and Aspect	55
Selecting Screen Aspect	55
Moving Image with 16:9 D. Image Shift	57
Moving Image with 4:3 D. Image Shift	58
Resetting the Image Shift	58
Selecting Aspect Ratio	59
Types of Aspect Ratios	59
How to Select an Aspect Ratio	60
Selecting an Image Mode	61
Image modes	61
How to Select an Image Mode	61
Turning Off the Projector	62
Useful Functions Available During a Presentation	63
Useful Functions Available During a Presentation	64
Blackened Out an Image Temporarily	64
Freezing the Picture	64
Adjusting the Volume	65
Muting the Sound	65
Zooming an Image	66
Showing the Elapsed Time	67
Setting Functions from Menus	69
How to Use Menus	70
Menu Configuration	70
Basic Operation of Menu	71
Setting Display Status	73
Selecting an Image Projection Mode	73
Selecting an Input Signal Type (ANALOG PC)	74
Selecting an Input Signal Type (VIDEO)	74
Selecting an Input Signal Type (COMPONENT)	75
Adjusting Input Signal (ANALOG PC) - Total Dots	75
Adjusting Input Signal (ANALOG PC) - Tracking	76
Adjust Input Signal (ANALOG PC) - Horizontal position	76
Adjust Input Signal (ANALOG PC) - Vertical position	77
Adjust Input Signal (ANALOG PC) - Horizontal pixels	77
Adjust Input Signal (ANALOG PC) - Vertical pixels	78
Selecting HDMI Input Level	78
Select HDMI Over Scan	79
Performing Progressive Processing	79
Selecting a Menu Position	80
Correcting the Screen Color	80
Reversing projection	81
Capturing a Logo	82
Selecting the User Logo Display Position	82
No Signal Screen	83
Screen When Blank	83
Selecting a Logo at Startup	84
Selecting Aspect Ratio of Screen	84
Setting the Image Quality	85
Selecting an Image Quality	85
Adjusting the Brightness	86
Adjusting the Contrast	86
Adjusting the Sharpness	87
Making a Gamma Correction	87
Making Color Adjustment (HDMI/DIGITAL PC/ANALOG PC)	88
Making Color Adjustment (COMPONENT/ VIDEO)	88
Making Advanced Adjustment (Noise reduction)	89
Making Advanced Adjustment (Dynamic gamma)	89
Making Advanced Adjustment (Auto fleshtone)	90
Adjusting Fine Color Adjustment (6-axis color adjust)	90
Reducing the Lamp Brightness	91
Resetting the Image Settings	91
Setting Various Function	92
Setting Auto Setup Function	92
Selecting the Power Management Mode	92
Skip the POWER Button Operation	93
Enabling/Disabling the Beep	93
Prohibiting the Projector Operation	94
Setting up the Remote Control Channel	94
Selecting a Display Language	95
Showing/hiding the Guide Screen	95
Turning on/off LED Illumination	96
Extending the Menu Display Time	96
Setting a Password	97
Registering a Password	97
Resetting the Lamp Counter	98
About the Display of the Lamp Counter	98
Turning On/Off the Network Function	99
Initializing network settings	100
Resetting to the Default Setting	100
Checking the Information of the Projector	101
Connecting the Projector to Network	103
Setting an IP Address	104
Setting IP Address of the Computer	104
Resetting the IP Address Setting of the Computer	105
Setting Network	106
Displaying the Network Configuration Screen	106
Setting the Network	107
Resetting the Network Setting	112
Error Notification Message	113
Projector Control	114
Appendix	115
Troubleshooting	116
WARNING Lamp Flash Patterns	116
Symptoms and Solutions	117
You cannot turn on the projector.	117
You cannot project an image from the projector.	117
You cannot hear sound.	118
The projected image is blur.	119
You cannot project an image appropriately.	119
The projector is forced to be turned off.	119
You cannot operate the remote control.	120
Maintenance	121
Cleaning the Projector	121
Cleaning and Replacing the Air Filter	122
Cleaning the Air Filter	122
Replacing the Air Filter	122
Replacing the Lamp	123
About the Replacing Lamp	123
Replacing the Lamp	124
Relationship between Aspect and Screen Aspect	125
When Projecting an Image from a Computer	125
When Projecting an Image from Image Software	127
Supported Computer Signal Types	128
Relationship between Screen Size and Projecting Distance	129
Glossary	130
Specifications	134
Projector	134
Remote Control	134
External View	135
ANALOG PC-2/COMPONENT IN terminal	135
Service Port (CONTROL)	136
Index	137
Numerics	137
A	137
B	137
C	137
D	137
F	137
G	137
H	137
I	137
K	138
L	138
M	138
N	138
O	138
P	138
R	138
S	138
T	138
V	139
W	139
Z	139