Carvin UX1000-MC UX1000-MC Product Manual - Page 3

UX1000 FRONT AND REAR RECEIVER PANEL CONTROLS LCD PANEL DISPLAY 2 3 6 5 4 1 10 789 UX1000 RECEIVER FRONT PANEL FEATURES 1. POWER SWITCH Depress to power the receiver. 2. UP BUTTON Depress to increase the number and set the operation mode. 3. DOWN BUTTON Depress to decrease the number and set the operation mode. 4. SET BUTTON Depress to set up the operation mode. 5. LCD PANEL Clearly displays the operation mode 6. VOLUME CONTROL Adjusts the output audio level to your amp or mixer. If distortion occurs, reduce the level. REAR PANEL FEATURES 7. DC POWER INPUT Use AC power adapter, which supplies 12V DC. 8. UNBALANCED 1/4" AUDIO OUTPUT JACK 1/4" phone jack can be connected to an unbalanced input of a mixer. 9. BALANCED XLR AUDIO OUTPUT JACK A standard XLR microphone cable can be used to connect the receiver output to a balanced input on a mixer. 10. ANTENNA Dual antenna for Diversity signal reception. UX-DR DUAL RACKMOUNT ADAPTER With the optional UX-DR adapter, you can mount one or two receivers. Remove the front panel of the mounting adapter to mount the second receiver. 1. AF signal 2. RF signal 3. Display for GROUP mode 4. Display for LOCK mode 5. Display for set FREQ. mode 6. Frequency display 7. Diversity display (A or B receiver) 8. Battery display for the transmitter 9. Group channel display 1. SETTING GROUP CHANNEL FREQ. DISPLAYED A. GROUP NUMBER SET UP Press the "SET" button for three seconds until "FREQ" shows up in the LCD display. Press the "SET" button a 2nd time to display the frequency number. Press "UP" or "DOWN" to increase or decrease the group number. B. CHANNEL SET UP After step A. press "SET" a 3rd time to display "CH", press "UP" or "DOWN" to change the CH number. Press "SET" again and the receiver will store the channel. GROUP DISPLAYED GROUP NUMBER SET UP Press the "SET" button for three seconds until the "G" group number shows in the LCD. Press the "SET" button a 2nd time to display the frequency number. Press "UP" or "DOWN" to increase or decrease the group number. CHANNEL SET UP After the group set up press "SET" a 3rd time to display "CH", press "UP" or "DOWN" to change the "CH" number. Press "SET" again and the receiver will store the channel. 2. SETTING FREQUENCY FREQ. DISPL Press the "SET" button for three seconds until "FREQ" shows up in the LCD display. Press "UP" or "DOWN" to increase or decrease the frequency number. Press "SET" again and the receiver will store the frequency. GROUP DISPLAYED Press the "SET" button for three seconds until the "G" group number shows in the LCD. Press "SET" again and the frequency starts flashing. Press "SET" until the "FREQ" shows use the "UP" or "DOWN" buttons to change the group digit. Press "SET" again the receiver will store the channel. 3. SETTING LOCK-ON FREQ. DISPLAYED Press "SET" button for three seconds until "FREQ" shows in the LCD. Press "SET" again and the Group number starts flashing. Press "SET" again until the frequency starts flashing then press "SET" to start the lock-on setting. Press "UP" button for lock-on mode and "DOWN" button for lock-off mode. Re-press "SET" and the lock function will store. GROUP DISPLAYED Press "SET" button for three seconds until the Group number shows. Re-press "SET" and the frequency starts flashing. Press "SET" again till "FREQ" show up, re-press "SET" button till "LOCK OFF" starts flashing then you can proceed the lock-on setting. (2) Press "UP"" button for lock-on mode and "DOWN" button for lock-off mode. Re-press "SET" button the lock function will store. 4. RELIEVED LOCK-ON Press "SET" button three seconds till "LOCK ON" show up, then press "DOWN" button plus "SET" button to store the lock-on relieved. 5. Pressing any button will display "LOCK ON" during Lock On mode. This setting remains until it is disabled. Turning the unit off will not disable the Lock On mode.