Carvin UX1000-MC UX1000-MC Product Manual - Page 4
Umc1000 Hand Held Mic, Ubp1000 Belt-pack Transmitter
View all Carvin UX1000-MC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
FIG. A click sides battery case replace slides down batteries FIG. B Sensitivity fine gain settings Set to 0 for instruments GAIN -20 -6 0 Set to -20 for mics Antenna UP Button Down Button Hold to release battery tray UBP1000 BELT-PACK TRANSMITTER 1. BATTERY INSTALLATION FIG. A Alkaline AA batteries are recommended. Hold on to the belt clip buttons to release battery tray. Insert fresh AA alkaline batteries. Slide the belt clip back until it locks. BELT PACK SET-UP FIG. A 1. METAL CASE & BELT CLIP The metal case provides extra protection for the transmitter and the plastic belt clip keeps it safe and at your side. Hold on to the belt clip buttons and slide the transmitter up to access push up to access front and rear controls the front and rear controls. 2. SENSITIVITY FIG. B The transmitter's sensitivity controls are located on the rear. Use the mini screwdriver to first set the Sensitivity switch to 0 for instruments or -20 for microphones. Use the mini screwdriver to make fine gain adjustments to the Sensitivity AF Gain Transmitter ON/OFF Switch for optimal transmitter volume. Decrease the gain if distortion is heard. 3. INPUT CONNECTOR The mini XLR input jack will connect a lavaliere mic, headset mic, or instrument cable to Push round button the transmitter. Line up the notches on the side of the jack and plug. Push in until cable to release cable locks into the jack. To unplug the mini XLR cable, press the round release button on the cable to unlock it from the jack. LCD Display 4. TRANSMITTER ON SWITCH Turn the receiver volume down before turning the transmitter power ON. The transmitter ON-OFF switch is located at the top of the unit. SET Button(1) 5. FREQUENCY ADJUSTING Hold "SET" button for 3 seconds to activate frequency. Once you see "MHZ" blinking, you are ready to select your desired frequency by using "UP" and "DOWN" buttons. Press the "SET" button again to store your changes. 6. TO ACTIVATE "LOCK MODE" Hold on to "UP" button for 3 seconds to activate "LOCK MODE", press again to unlock. UX-LP1 UXGT UX-HM2 UX-HM2 HEADSET MIC Connect the mic cable to the transmitter's mini XLR input jack. Place the mic on vocalist head with the headband resting comfortably on the rear of the neck. Keep the mic a minimum of 2 inches from the mouth. Adjust the mic position to minimize air from hitting the mic. UX-LP1 LAVALIERE MIC Connect the Lavaliere mic cable to the transmitter's mini XLR input jack. Clip the mic to a shirt. For optimum sound, position the mic as close to the mouth with the top of the mic facing up. Test out various positions along the center of the chest to determine the ideal mic placement. This may vary from person to person as each voice projects uniquely. UXGT INSTRUMENT CABLE Connect the cable to the belt-pack transmitter's mini XLR input jack. Plug the 1/4" connector into a guitar. Turn the receiver volume down before turning the transmitter power ON. FIG. F POWER DOWN SET UP MUTE FIG. D FIG. E UMC1000-ID color coded rings FIG. C unscrew the handle to replace batteries UMC1000 HAND HELD MIC 1. BATTERY INSTALLATION FIG. C While holding the higher part of the transmitter body, unscrew the handle. Install fresh AA alkaline batteries. Replace the handle and turn clockwise until tight. 2. POWER ON FIG. D Switch to POWER ON position. 3. MUTE SWITCH FIG. D Used to mute audio without losing RF connection. 4. UMC1000-ID 7 COLOR CODED RINGS FIG. E Use the UMC1000-ID 7 color coded rings to identify multiple microphones in use. Each color can correspond to a different wireless channel. PROGRAMMING HAND HELD MIC FIG. F 1. SETTING GROUP CHANNEL GROUP SET UP Press "SET" button for three seconds until the "MHZ" shows and then re-press "SET" until the group digit shows. Now you can press "UP" or "DOWN" button one sec. to increase or decrease group number CHANNEL SET UP Follow the GROUP SET UP procedures, then press "SET" again and the frequency displays, press "UP" or "DOWN" to increase or decrease the frequency. Press "SET" to store the mic frequency. GROUP DISPLAYED Press "SET" for three seconds until the Group digit shows. Then re-press "UP" or "DOWN" button to increase or decrease the group number. Press "SET" again and the frequency displays. Press "UP" or "DOWN" to increase or decrease the frequency. Press "SET" again and the mic will store the frequency.