Casio XJ-M140 User Manual - Page 61

Input source: RGB or HDMI PC, Power on: Write

Get Casio XJ-M140 PDF manuals and user guides View all Casio XJ-M140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

z See the "Command List" for details about command names and settings. z All commands use ASCII characters and decimal format integers. z The projector will return a question mark (?) when it is sent a command it cannot recognize. Also, any command that attempts to set a value that is outside the applicable allowable range will be ignored. z If the projector is performing a process initiated by a previously sent command, a projector key operation, or a remote controller key operation, send of the next command must wait until the projector completes the previous process. Command List z Only the following functions are supported while the projector is turned off. Do not try to send any other command to the projector. z Power on/off: Read z Power on: Write z Get light time: Read z Input of a valid signal must be in progress in order to use a command to turn on blank screen or change the aspect ratio. R: Read enabled W: Write enabled Function Command Name RW Setting Range Power On/Off: PWR RW 0: Off, 1: On Input Switching: 0: Switches the input source to the COMPUTER terminal and changes the COMPUTER terminal setting to RGB. 1: Switches the input source to COMPUTER terminal and changes the COMPUTER terminal setting to component. 2: Switches the input source to Video. 5: Switches the input source to USB. This setting is supported only when the projector is equipped with a USB function and the USB application is running. 6: Switches the input source to COMPUTER terminal and changes the COMPUTER terminal setting to Auto. 7: Switches the input source to HDMI. 9: Switches the input source to S-video. SRC RW 0: RGB, 1: Component, 2: Video, 5: USB, 6: Auto (RGB/Component), 7: HDMI, 9: S-video Blank Screen: Switches the blank screen on or off. BLK RW 0: Off, 1: On Volume: Specifies a value to adjust the volume level. This setting is applied to the input source signal that is currently being projected by the projector. VOL RW 0-30 Color Mode: Selects the color mode. Aspect Ratio: Specifies the aspect ratio. PST RW 1: Graphics, 2: Theater, 3: Standard, 4: Blackboard, 5: Game ARZ RW 0: Normal*1, 1: 16:9, 2: Normal*2, 3: Letter Box, 4: Full, 5: True Get Light Time: Gets the light time from the projector. LMP R 0- Unit: Hours *1 Input source: RGB or HDMI (PC) *2 Input source: Video, S-video, component or HDMI (DTV) 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
61
See the “Command List” for details about command names and settings.
All commands use ASCII characters and decimal format integers.
The projector will return a question mark (?) when it is sent a command it cannot recognize. Also,
any command that attempts to set a value that is outside the applicable allowable range will be
ignored.
If the projector is performing a process initiated by a previously sent command, a projector key
operation, or a remote controller key operation, send of the next command must wait until the
projector completes the previous process.
Command List
Only the following functions are supported while the projector is turned off. Do not try to send any
other command to the projector.
Input of a valid signal must be in progress in order to use a command to turn on blank screen or
change the aspect ratio.
R: Read enabled
W: Write enabled
Power on/off: Read
Power on: Write
Get light time: Read
Function
Command
Name
RW
Setting Range
Power On/Off:
PWR
RW
0: Off, 1: On
Input Switching: 0:
Switches the input source to the
COMPUTER terminal and changes the
COMPUTER terminal setting to RGB.
1:
Switches the input source to COMPUTER
terminal and changes the COMPUTER
terminal setting to component.
2:
Switches the input source to Video.
5:
Switches the input source to USB. This
setting is supported only when the
projector is equipped with a USB function
and the USB application is running.
6:
Switches the input source to COMPUTER
terminal and changes the COMPUTER
terminal setting to Auto.
7:
Switches the input source to HDMI.
9:
Switches the input source to S-video.
SRC
RW
0: RGB, 1: Component,
2: Video, 5: USB,
6: Auto (RGB/Component),
7: HDMI, 9: S-video
Blank Screen:
Switches the blank screen on or off.
BLK
RW
0: Off, 1: On
Volume:
Specifies a value to adjust the volume level. This
setting is applied to the input source signal that is
currently being projected by the projector.
VOL
RW
0-30
Color Mode:
Selects the color mode.
PST
RW
1: Graphics, 2: Theater,
3: Standard, 4: Blackboard,
5: Game
Aspect Ratio:
Specifies the aspect ratio.
ARZ
RW
0: Normal
*
1
, 1: 16:9,
2: Normal
*
2
, 3: Letter Box,
4: Full, 5: True
Get Light Time:
Gets the light time from the projector.
LMP
R
0- Unit: Hours
*
1 Input source: RGB or HDMI (PC)
*
2 Input source: Video, S-video, component or HDMI (DTV)