Chamberlain B550 B550 B552 B750 Owner s Manual - English - Page 38

TIMER-TO-CLOSE (DO NOT enable on one-piece doors), Remote Control and Keyless Entry - smart

Get Chamberlain B550 PDF manuals and user guides View all Chamberlain B550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Operation TIMER-TO-CLOSE (DO NOT enable on one-piece doors) The Timer-to-Close feature is not available on all door controls. Below is a list of door controls with the Timer-toClose feature: 041A7305-1 Smart Control Panel and 041A7327-1 Motion Detecting Control Panel The Timer-to-Close feature automatically closes the garage door after a specified time period. DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors. Factory default is set to off. The garage door opener will beep and the lights will flash before closing the door. The TTC feature will deactivate if the garage door encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door will close when the garage door opener is activated. TTC WILL NOT work if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned. This feature is NOT intended to be the primary method of closing the door. A keyless entry should be installed in the event of an accidental lock out when using this feature. Remote Control and Keyless Entry Pre-programmed remote controls (2) included, no need to program the remote. To add or reprogram a remote control, follow the instructions below. Older Chamberlain remote controls are NOT compatible, see page 43 for compatible accessories. PROGRAM USING THE DOOR CONTROL 1. Press the LEARN button on the door control to enter Programming Mode. 2. Press the LEARN button again, the LED will flash once. 3. Remote Control: Press the button on the remote control that you wish to operate your garage door. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed. 1 The command LED will flash once. 2 The command LED will flash once again. or or 3 OR ???? PIN To watch a video, go to tinyurl.com/lcsf6xt HomeLink® If your vehicle is equipped with HomeLink, a Compatibility BridgeTM (not included) may be necessary for certain vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
38
Operation
TIMER-TO-CLOSE (DO NOT enable on one-piece doors)
The Timer-to-Close feature is not available on all door controls. Below is a list of door controls with the Timer-to-
Close feature:
041A7305-1 Smart Control Panel and 041A7327-1 Motion Detecting Control Panel
The Timer-to-Close feature automatically closes the garage door after a specified time period.
DO NOT enable TTC
if operating a one-piece door. TTC is to be used ONLY with sectional doors.
Factory default is set to off. The
garage door opener will beep and the lights will flash before closing the door. The TTC feature will deactivate if the
garage door encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage
door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are
correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door
will close when the garage door opener is activated. TTC WILL NOT work if the garage door opener is operating by
battery power or if the safety reversing sensors are misaligned. This feature is NOT intended to be the primary
method of closing the door.
A keyless entry should be installed in the event of an accidental lock out when
using this feature.
Remote
Control
and
Keyless
Entry
Pre-programmed
remote
control
s
(2)
included,
no
need
to
program
the
remote.
To
add
or
reprogram
a
remote
control,
follow
the
instructions
below.
Older
Chamberlain
remote
controls
are
NOT
compatible,
see
page
43
for
compatible
accessories.
PROGRAM
USING
THE
DOOR
CONTROL
1.
Press the LEARN button on the door control to enter Programming Mode.
2.
Press the LEARN button again, the LED will flash once.
3.
Remote Control:
Press the button on the remote control that you wish to operate your garage door.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry
keypad. Then press the ENTER button.
The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.
The command LED will flash once.
or
The command LED will flash once again.
1
2
OR
PIN
?
?
?
?
3
or
To watch a video, go to
tinyurl.com/lcsf6xt
HomeLink
®
If your vehicle is equipped with HomeLink, a Compatibility Bridge
TM
(not included) may be necessary for certain
vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed.