Cisco 3550-12T Hardware Installation Guide - Page 34

Site Requirements, Verifying Package Contents - 12g

Get Cisco 3550-12T - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320521411
View all Cisco 3550-12T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Preparing for Installation Chapter 2 Switch Installation Site Requirements When determining where to place the switch, be sure to observe these requirements: • Operating environment is within the ranges listed in Appendix A, "Technical Specifications." • Clearance to front and rear panels is such that - Front-panel indicators can be easily read. - Access to ports is sufficient for unrestricted cabling. - Rear-panel power connector is within reach of an AC power receptacle. • Airflow around the switch and through the vents is unrestricted. • Temperature around the unit does not exceed 113° F (45° C). Note If the switch is installed in a closed or multirack assembly, the temperature around it might be greater than normal room temperature. • Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting fixtures. Make sure that the cabling is safely away from other devices that might damage the cables. • For sites requiring compliance to Telcordia GR-1089-CORE Intra-building Lightning requirements, all 10/100 and 10/100/1000 ports must be connected with shielded cable grounded at both ends. Verifying Package Contents Note Carefully remove the contents from the shipping container, and check each item for damage. If any item is missing or damaged, contact your Cisco representative or reseller for support. Return all packing material to the shipping container, and save it. The switch is shipped with these items: • This Catalyst 3550 Series Hardware Installation Guide • Where to Find the Catalyst 3550 Documentation flyer • Product registration card • AC power cord (AC-powered switches) • One RJ-45-to-DB-9 adapter cable • Mounting kit containing: - Four rubber feet for mounting the switch on a table - Two 19-inch rack-mounting brackets - Four Phillips flat-head screws for attaching the brackets to the switch (Catalyst 3550-12T and 3550-12G switches) - Six Phillips flat-head screws for attaching the brackets to the switch (Catalyst 3550-24, 3550-24-DC, 3550-24-FX, 3550-24PWR, and 3550-48 switches) - Four Phillips machine screws for attaching the brackets to a rack Catalyst 3550 Switch Hardware Installation Guide 2-4 OL-6155-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
2-4
Catalyst 3550 Switch Hardware Installation Guide
OL-6155-01
Chapter 2
Switch Installation
Preparing for Installation
Site Requirements
When determining where to place the switch, be sure to observe these requirements:
•
Operating environment is within the ranges listed in
Appendix A,
“
Technical Specifications.
”
•
Clearance to front and rear panels is such that
–
Front-panel indicators can be easily read.
–
Access to ports is sufficient for unrestricted cabling.
–
Rear-panel power connector is within reach of an AC power receptacle.
•
Airflow around the switch and through the vents is unrestricted.
•
Temperature around the unit does not exceed 113
°
F (45
°
C).
Note
If the switch is installed in a closed or multirack assembly, the temperature around it might be greater
than normal room temperature.
•
Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent
lighting fixtures. Make sure that the cabling is safely away from other devices that might damage
the cables.
•
For sites requiring compliance to Telcordia GR-1089-CORE Intra-building Lightning requirements,
all 10/100 and 10/100/1000 ports must be connected with shielded cable grounded at both ends.
Verifying Package Contents
Note
Carefully remove the contents from the shipping container, and check each item for damage. If any item
is missing or damaged, contact your Cisco representative or reseller for support. Return all packing
material to the shipping container, and save it.
The switch is shipped with these items:
•
This
Catalyst 3550 Series Hardware Installation Guide
•
Where to Find the Catalyst 3550 Documentation
flyer
•
Product registration card
•
AC power cord (AC-powered switches)
•
One RJ-45-to-DB-9 adapter cable
•
Mounting kit containing:
–
Four rubber feet for mounting the switch on a table
–
Two 19-inch rack-mounting brackets
–
Four Phillips flat-head screws for attaching the brackets to the switch (Catalyst 3550-12T
and 3550-12G switches)
–
Six Phillips flat-head screws for attaching the brackets to the switch (Catalyst 3550-24,
3550-24-DC, 3550-24-FX, 3550-24PWR, and 3550-48 switches)
–
Four Phillips machine screws for attaching the brackets to a rack