Cisco 3550-12T Hardware Installation Guide - Page 68

Wiring the DC-Input Power Source

Get Cisco 3550-12T - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320521411
View all Cisco 3550-12T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Connecting to DC Power Appendix C DC Power Connections Wiring the DC-Input Power Source Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Caution You must connect the Catalyst 3550-24-DC switch only to a DC-input power source that has an input supply voltage from -36 to -72 VDC. If the supply voltage is not in this range, the switch might not operate properly or might be damaged. Caution The switch must be installed with 5 A-branch-circuit protection. Note This installation must comply with all applicable codes. To wire the switch to a DC-input power source, follow these steps: Step 1 Locate and remove the terminal block plug (see Figure C-4). Figure C-4 Terminal Block Plug 60530 Catalyst 3550 Multilayer Switch Hardware Installation Guide C-4 OL-6155-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
C-4
Catalyst 3550 Multilayer Switch Hardware Installation Guide
OL-6155-01
Appendix C
DC Power Connections
Connecting to DC Power
Wiring the DC-Input Power Source
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003
Caution
You must connect the Catalyst 3550-24-DC switch only to a DC-input power source that has an input
supply voltage from
–
36 to
–
72 VDC. If the supply voltage is not in this range, the switch might not
operate properly or might be damaged.
Caution
The switch must be installed with 5 A-branch-circuit protection.
Note
This installation must comply with all applicable codes.
To wire the switch to a DC-input power source, follow these steps:
Step 1
Locate and remove the terminal block plug (see
Figure C-4
).
Figure C-4
Terminal Block Plug
60530