Cisco 3750 System Message Guide - Page 30

DOT1X Messages

Get Cisco 3750 - Catalyst EMI Switch PDF manuals and user guides
UPC - 746320805139
View all Cisco 3750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

DOT1X Messages Chapter 2 Message and Recovery Procedures DOT1X Messages This section contains the 802.1x messages. Error Message DOT1X-4-MEM_UNAVAIL: Memory was not available to perform the 802.1X action. Explanation This message means that the system memory is not sufficient to perform the 802.1x authentication. Recommended Action Reduce other system activity to reduce memory demands. Error Message DOT1X-4-MSG_ERR: Unknown message event received. Explanation This message means that the 802.1x process received an unknown message event. Recommended Action Restart the 802.1x process by entering the dot1x system-auth-control global configuration command. If this message recurs, reload the device. Error Message DOT1X-4-PROC_START_ERR: Dot1x unable to start. Explanation This message means that the system failed to create the 802.1x process. Recommended Action Restart the 802.1x process by entering the dot1x system-auth-control global configuration command. If this message recurs, reload the device. Error Message DOT1X-4-UNKN_ERR: An unknown operational error occurred. Explanation This message means that the 802.1x process cannot operate because of an internal system error. Recommended Action No action is required. Error Message DOT1X-5-ERR_CHANNELLING: Dot1x can not be enabled on Channelling ports. Explanation This message means that 802.1x could not be enabled on the channeling port. Trying to set 802.1x port-control to auto or force-unauthorized (force_unauth) mode on a channeling port, which is not allowed, caused this condition. Recommended Action Disable channeling on the interface, and then enable 802.1x. Error Message DOT1X-5-ERR_DYNAMIC: Dot1x can not be enabled on Dynamic ports. Explanation This message means that 802.1x could not be enabled on the dynamic mode port. Trying to set 802.1x port-control to auto or force-unauthorized (force_unauth) mode on a dynamic mode port, which is not allowed, caused this condition. Recommended Action Disable dynamic mode on the interface, and then enable 802.1x. 2-12 Catalyst 3750 Switch System Message Guide 78-16184-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2-12
Catalyst 3750 Switch System Message Guide
78-16184-04
Chapter 2
Message and Recovery Procedures
DOT1X Messages
DOT1X Messages
This section contains the 802.1x messages.
Error Message
DOT1X-4-MEM_UNAVAIL: Memory was not available to perform the
802.1X action.
Explanation
This message means that the system memory is not sufficient to perform the 802.1x
authentication.
Recommended Action
Reduce other system activity to reduce memory demands.
Error Message
DOT1X-4-MSG_ERR: Unknown message event received.
Explanation
This message means that the 802.1x process received an unknown message event.
Recommended Action
Restart the 802.1x process by entering the
dot1x system-auth-control
global
configuration command. If this message recurs, reload the device.
Error Message
DOT1X-4-PROC_START_ERR: Dot1x unable to start.
Explanation
This message means that the system failed to create the 802.1x process.
Recommended Action
Restart the 802.1x process by entering the
dot1x system-auth-control
global
configuration command. If this message recurs, reload the device.
Error Message
DOT1X-4-UNKN_ERR: An unknown operational error occurred.
Explanation
This message means that the 802.1x process cannot operate because of an internal
system error.
Recommended Action
No action is required.
Error Message
DOT1X-5-ERR_CHANNELLING: Dot1x can not be enabled on Channelling
ports.
Explanation
This message means that 802.1x could not be enabled on the channeling port. Trying to
set 802.1x port-control to
auto
or
force-unauthorized
(force_unauth) mode on a channeling port,
which is not allowed, caused this condition.
Recommended Action
Disable channeling on the interface, and then enable 802.1x.
Error Message
DOT1X-5-ERR_DYNAMIC: Dot1x can not be enabled on Dynamic ports.
Explanation
This message means that 802.1x could not be enabled on the dynamic mode port. Trying
to set 802.1x port-control to
auto
or
force-unauthorized
(force_unauth) mode on a dynamic mode
port, which is not allowed, caused this condition.
Recommended Action
Disable dynamic mode on the interface, and then enable 802.1x.