Cisco 3750 System Message Guide - Page 44

reload, show tech-support, the module as a Cisco module but identifies another problem with it. - setup

Get Cisco 3750 - Catalyst EMI Switch PDF manuals and user guides
UPC - 746320805139
View all Cisco 3750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

GBIC_SECURITY_CRYPT Messages Chapter 2 Message and Recovery Procedures Error Message GBIC_SECURITY-4-EEPROM_SECURITY_ERR: GBIC in [chars] failed security check. Explanation The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which the GBIC is inserted. Recommended Action Remove the GBIC from the port. Error Message GBIC_SECURITY-4-GBIC_INTERR: Internal error occurred in setup for GBIC interface [chars]. Explanation This message means that the system could not allocate resources or had some other problem during the setup for the specified SFP module interface. [chars] is the interface in which the SFP module is installed. Recommended Action Reload the switch by using the reload privileged EXEC command. If the problem persists, find out more about the error by using the show tech-support privileged EXEC command and by copying the error message exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools and about contacting Cisco, see the "Error Message Traceback Reports" section on page 1-5. GBIC_SECURITY_CRYPT Messages This section contains the Cisco GBIC module and SFP module security messages. The switch recognizes the module as a Cisco module but identifies another problem with it. Note The switch supports SFP modules and does not support GBIC modules. Although the error message text refers to GBIC interfaces and modules, the messages from the switch actually refer to the SFP module interfaces and modules. Error Message GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification check failed for GBIC interface [chars]. Explanation This message means that the SFP module was identified as a Cisco SFP module, but the system was unable to verify its identity. [chars] is the interface in which the module is installed. Recommended Action Check the list of supported SFP modules for this version of the system software. An upgrade might be required for newer modules. Otherwise, verify that the module was obtained from Cisco or from a supported vendor. 2-26 Catalyst 3750 Switch System Message Guide 78-16184-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2-26
Catalyst 3750 Switch System Message Guide
78-16184-04
Chapter 2
Message and Recovery Procedures
GBIC_SECURITY_CRYPT Messages
Error Message
GBIC_SECURITY-4-EEPROM_SECURITY_ERR: GBIC in [chars] failed security
check.
Explanation
The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which
the GBIC is inserted.
Recommended Action
Remove the GBIC from the port.
Error Message
GBIC_SECURITY-4-GBIC_INTERR: Internal error occurred in setup for GBIC
interface [chars].
Explanation
This message means that the system could not allocate resources or had some other
problem during the setup for the specified SFP module interface. [chars] is the interface in which
the SFP module is installed.
Recommended Action
Reload the switch by using the
reload
privileged EXEC command. If the
problem persists, find out more about the error by using the
show tech-support
privileged EXEC
command and by copying the error message exactly as it appears on the console or system log and
entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For
more information about these online tools and about contacting Cisco, see the
“Error Message
Traceback Reports” section on page 1-5
.
GBIC_SECURITY_CRYPT Messages
This section contains the Cisco GBIC module and SFP module security messages. The switch recognizes
the module as a Cisco module but identifies another problem with it.
Note
The switch supports SFP modules and does not support GBIC modules. Although the error message text
refers to GBIC interfaces and modules, the messages from the switch actually refer to the SFP module
interfaces and modules.
Error Message
GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification check failed for
GBIC interface [chars].
Explanation
This message means that the SFP module was identified as a Cisco SFP module, but the
system was unable to verify its identity. [chars] is the interface in which the module is installed.
Recommended Action
Check the list of supported SFP modules for this version of the system
software. An upgrade might be required for newer modules. Otherwise, verify that the module was
obtained from Cisco or from a supported vendor.