Cisco 7204 Installation Guide - Page 67

Installing the Brackets on the Chassis,

Get Cisco 7204 - VXR Router PDF manuals and user guides
UPC - 746320286631
View all Cisco 7204 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Chapter 3 Installing the Cisco 7204 Rack-Mounting the Cisco 7204 Figure 3-5 Rack-Mounting the Chassis in a 4-post Rack with Installed Cable-Management Brackets-Front Installation Shown EN 0 1 2 3 4 5 6 7 3 1 ENABLED PCMCIA EN RX 0 TX SERIAL-EIA/TIA-232 SLOT 1 EJECT SLOT 0 FE MII II MEN RJE4N5 RJL4IN5 K R 1O PWK O ENABLED RJ-45 CPU RESET RX 1 TX RX 0 2 TX RX 3 TX MII LINK RJ45 FAST ETHERNET 4 ETHERNET-10BFL 2 FAST ETHERNET INPUT/OUTPUT CONTROLLER 0 RX 4 TX Rack-mount bracket Cable-management bracket H9238 If you are rack-mounting a Cisco 7200 series router from the rear, the rack-mount brackets are installed at the rear of the chassis, and the cable-management brackets are installed at the front of the chassis. You must install both sets of brackets before you install the chassis in the rack. Installing the Brackets on the Chassis This section explains how to install the rack-mount and cable-management brackets at the front and the rear of the Cisco 7204. Before installing the chassis in the rack, you must install a rack-mount bracket on each side of the front or rear of the chassis. If you are rack-mounting the chassis from the front and you plan to use the cable-management brackets, you must install the cable-management brackets when you install the rack-mount brackets on the chassis. If you are rack-mounting the chassis from the rear, you may install the rack-mount and cable-management brackets separately; however, both sets of brackets must be installed on the chassis before the chassis is installed in the rack. The parts and tools required for installing the rack-mount and cable-management brackets are listed in the "Tools for Installation" section on page 2-10 in Chapter 2, "Preparing for Installation" of this guide. Warning After attaching the brackets, and to avoid injury, we recommend that two people install the chassis in the rack. (One person should support the chassis in the rack while the second person installs the fasteners.) OL-5101-02 Cisco 7204 Installation and Configuration Guide 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
3-5
Cisco 7204 Installation and Configuration Guide
OL-5101-02
Chapter 3
Installing the Cisco 7204
Rack-Mounting the Cisco 7204
Figure 3-5
Rack-Mounting the Chassis in a 4-post Rack with Installed Cable-Management
Brackets—Front Installation Shown
If you are rack-mounting a Cisco 7200 series router from the rear, the rack-mount brackets are installed
at the rear of the chassis, and the cable-management brackets are installed at the front of the chassis. You
must install both sets of brackets
before
you install the chassis in the rack.
Installing the Brackets on the Chassis
This section explains how to install the rack-mount and cable-management brackets at the front and the
rear of the Cisco 7204. Before installing the chassis in the rack, you must install a rack-mount bracket
on each side of the front or rear of the chassis. If you are rack-mounting the chassis from the front and
you plan to use the cable-management brackets, you must install the cable-management brackets when
you install the rack-mount brackets on the chassis.
If you are rack-mounting the chassis from the rear, you may install the rack-mount and
cable-management brackets separately; however, both sets of brackets must be installed on the chassis
before the chassis is installed in the rack.
The parts and tools required for installing the rack-mount and cable-management brackets are listed in
the
“Tools for Installation” section on page 2-10
in
Chapter 2, “Preparing for Installation”
of this guide.
Warning
After attaching the brackets, and to avoid injury, we recommend that two people install the chassis
in the rack. (One person should support the chassis in the rack while the second person installs the
fasteners.)
ENABLED
MII
LINK
RJ45
FAST ETHERNET
0
0
2
4
1
3
EN
0
7
1
2
3
4
5
6
SERIAL-EIA/TIA-232
ETHERNET-10BFL
EN
RX
0
1
2
3
4
TX
RX
TX
RX
TX
RX
TX
RX
TX
H9238
FAST ETHERNET INPUT/OUTPUT CONTROLLER
ENABLED
PCMCIA
EJECT
SLOT 0
SLOT 1
FE MII
Rack-mount
bracket
Cable-management bracket