Cisco CISCO2509-CH Getting Started Guide - Page 13

Mounting the Controller on a Wall (Rack-Mount Brackets) - 8 port switch

Get Cisco CISCO2509-CH - 2509 Enet/ Dual Serial/8 Asynch Router Req. Sw Feat Pk PDF manuals and user guides
UPC - 746320009506
View all Cisco CISCO2509-CH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Step 3 Place the switch on the table or shelf near an AC power source. Note Allow 3 inches of space around the controller ventilation openings to prevent airflow restriction and overheating. Step 4 Step 5 After the controller is mounted on a shelf or desk, perform the following tasks to complete the installation: • Connecting the Controller Console Port • Securing the Power Adapter Cable • Connecting to the Network For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on page 23. Mounting the Controller on a Wall (Rack-Mount Brackets) The controller can be mounted on a wall using an optional rack-mount bracket kit that is not included with the controller. You can order a kit with 19-inch rack mounting brackets and hardware from Cisco. The kit part number is AIR-CT2504-RMNT. Warning Read the wall-mounting carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 To mount the controller on a wall using rack-mount brackets, follow these steps: Step 1 Attach the 19-inch brackets to each side of the 2504 controller as shown in Figure 5 with #10-32 flat head screws provided in the kit. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
13
Step 3
Place the switch on the table or shelf near an AC power source.
Note
Allow 3 inches of space around the controller ventilation openings to prevent airflow
restriction and overheating.
Step 4
After the controller is mounted on a shelf or desk, perform the following tasks to complete
the installation:
•
Connecting the Controller Console Port
•
Securing the Power Adapter Cable
•
Connecting to the Network
Step 5
For configuration instructions about using the CLI setup program, see the
“Running the
Bootup Script and Power-On Self Test” section on page 23
.
Mounting the Controller on a Wall (Rack-Mount Brackets)
The controller can be mounted on a wall using an optional rack-mount bracket kit that is not included
with the controller. You can order a kit with 19-inch rack mounting brackets and hardware from
Cisco. The kit part number is AIR-CT2504-RMNT.
Warning
Read the wall-mounting carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous
situation to people and damage to the system.
Statement 378
To mount the controller on a wall using rack-mount brackets, follow these steps:
Step 1
Attach the 19-inch brackets to each side of the 2504 controller as shown in
Figure 5
with
#10-32 flat head screws provided in the kit.