Cisco SRW248G4P User Guide - Page 13

Configuration Using the Console Interface, - default password

Get Cisco SRW248G4P PDF manuals and user guides View all Cisco SRW248G4P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Chapter 4 Configuration Using the Console Interface Versions The Versions screen displays the Boot Version, Software Version, Loader Version and the Hardware Version. Management Settings The Management Settings screen displays the Serial Port Configuration. Versions Boot Version This file runs when the Switch is turned on. It performs power-on diagnostics and loads the operating system for the Switch. Software Version This file contains the programming code that runs the Switch. Loader Version This file loads the software from storage memory to main memory. Hardware Version The current hardware setup of the Switch. General Information The General Information screen displays the System Description, System Up Time, System Mac Address, System Contact, System Name and System Location. General Information Management Settings Serial Port Configuration The Serial Port Configuration screen displays the current setting for the baud rate. The baud rate can be changed by selecting Edit then using the spacebar to toggle through the different baud rates. Use the Save action to set the new baud rate. Serial Port Configuration User & Password Settings The User & Password Settings screen displays user account information on the Switch. The default account is the admin account. To add a new user, use the arrow keys to select Edit and then press the Enter key, then enter the user name of the new account and assign a password to the account. The password must be re-entered into the Again Password column to confirm the password. 48-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet User & Password Settings 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
·
Configuration Using the Console Interface
48-Port 10/100 + 4-Port G±gab±t Sw±tch w±th WebV±ew and Power over Ethernet
Chapter 4
Versions
The
Versions
screen displays the Boot Version, Software
Version, Loader Version and the Hardware Version°
Versions
Boot Vers±on
This file runs when the Switch is turned on°
It performs power-on diagnostics and loads the operating
system for the Switch°
Software Vers±on
This file contains the programming
code that runs the Switch°
Loader Vers±on
This file loads the software from storage
memory to main memory°
Hardware Vers±on
The current hardware setup of the
Switch°
General Information
The
General Information
screen displays the System
Description, System Up Time, System Mac Address, System
Contact, System Name and System Location°
General Information
Management Settings
The
Management Settings
screen displays the Serial Port
Configuration°
Management Settings
Serial Port Configuration
The
Serial Port Configuration
screen displays the current
setting for the baud rate° The baud rate can be changed by
selecting
Ed±t
then using the
spacebar
to toggle through
the different baud rates° Use the
Save
action to set the
new baud rate°
Serial Port Configuration
User & Password Settings
The
User & Password Settings
screen displays user account
information on the Switch° The default account is the
adm±n
account° To add a new user, use the
arrow keys
to
select
Ed±t
and then press the
Enter
key, then enter the
user name of the new account and assign a password to
the account° The password must be re-entered into the
Aga±n Password
column to confirm the password°
User & Password Settings