Cisco SRW248G4P User Guide - Page 52

SNMP > Notification Recipient, Admin, Admin > User Authentication, SNMPv1

Get Cisco SRW248G4P PDF manuals and user guides View all Cisco SRW248G4P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Chapter 5 Configuring the Switch SNMP > Notification Recipient UDP Port Specifies the UDP port number used by the trap manager. Timeout The number of seconds to wait for an acknowledgment before resending an inform message. (Range: 0-2147483647 centiseconds; Default: 1500 centiseconds) Retry times The maximum number of times to resend an inform message if the recipient does not acknowledge receipt. (Range: 0-255; Default: 3) Admin The Admin tab provides access to system administration settings and tools. It includes the following screens: Admin > User Authentication SNMP > Notification Recipient Recipient IP IP address of a new management station to receive notification messages. NotificationType Notifications are sent as traps or inform messages. The informs option is only available for version 2c and 3 hosts. (Default: Traps are used) SNMPv1,2 Community String Specifies a valid community string for the new trap manager entry. (Range: 1-32 characters, case sensitive) Notification Version Indicates if the user is running SNMP v1 or v2c. (Default: v1) SNMPv3 User Name The name of user connecting to the SNMP agent. (Range: 1-32 characters) Security Level When trap version 3 is selected, you must specify one of the following security levels. (Default: noAuthNoPriv) • noAuthNoPriv There is no authentication or encryption used in SNMP communications. (This is the default for SNMPv3.) • AuthNoPriv SNMP communications use authentication, but the data is not encrypted (only available for the SNMPv3 security model). • AuthPriv SNMP communications use both authentication and encryption (only available for the SNMPv3 security model). Admin > User Authentication The Switch supports up to 6 user names and passwords for management access (console and web interfaces). The default user name is "admin" with no password. You should therefore assign a new password for the "admin" user account and store it in a safe place. The default "admin" account cannot be deleted from the system. As well as the default "admin" account, up to five other user-defined accounts can be created on the Switch. To create a new user account, enter a user name and password up to eight characters long, confirm the password, and then click Add. To change the password for a specific user, select the user name from the list, enter the new password, confirm the password by entering it again, and then click Update. 48-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Chapter ´
Configuring the Switch
48
48-Port 10/100 + 4-Port G±gab±t Sw±tch w±th WebV±ew and Power over Ethernet
SNMP > Notification Recipient
SNMP > Notification Recipient
Rec±p±ent IP
IP address of a new management station to
receive notification messages°
Not±f±cat±on Type
Notifications are sent as traps or inform
messages° The informs option is only available for version
2c and 3 hosts° (Default:
Traps are used
)
SNMPv1,2
Commun±ty Str±ng
Specifies a valid community string
for the new trap manager entry° (Range: 1-32 characters,
case sensitive)
Not±f±cat±on Vers±on
Indicates if the user is running
SNMP v1 or v2c° (Default:
v1
)
SNMPv3
User Name
The name of user connecting to the SNMP
agent° (Range: 1-32 characters)
Secur±ty Level
When trap version 3 is selected, you
must specify one of the following security levels° (Default:
noAuthNoPr±v
)
noAuthNoPr±v
There is no authentication or encryption
used in SNMP communications° (This is the default for
SNMPv3°)
AuthNoPr±v
SNMP communications use authentication,
but the data is not encrypted (only available for the SNMPv3
security model)°
AuthPr±v
SNMP communications use both authentication
and encryption (only available for the SNMPv3 security
model)°
•
•
•
UDP Port
Specifies the UDP port number used by the
trap manager°
T±meout
The
number
of
seconds
to
wait
for
an
acknowledgment before resending an inform message°
(Range:
0-2147483647
centiseconds;
Default:
1´00
cent±seconds
)
Retry t±mes
The maximum number of times to resend
an inform message if the recipient does not acknowledge
receipt° (Range: 0-255; Default:
³
)
Admin
The Admin tab provides access to system administration
settings and tools° It includes the following screens:
Admin > User Authentication
Admin > User Authentication
The Switch supports up to 6 user names and passwords
for management access (console and web interfaces)°
The default user name is “
adm±n
” with no password° You
should therefore assign a new password for the “admin”
user account and store it in a safe place° The default
“admin” account cannot be deleted from the system°
As well as the default “
adm±n
” account, up to five other
user-defined accounts can be created on the Switch° To
create a new user account, enter a user name and password
up to eight characters long, confirm the password, and
then click
Add
°
To change the password for a specific user, select the user
name from the list, enter the new password, confirm the
password by entering it again, and then click
Update
°