Cisco WAP200E-EU User Guide - Page 11

Installation, Overview, Personal Installation, Installation Location, External Antenna - wireless g exterior access point

Get Cisco WAP200E-EU - Small Business Wireless-G Exterior Access Point PDF manuals and user guides
UPC - 745883578627
View all Cisco WAP200E-EU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Chapter 4 Installation Chapter 4: Installation Overview This chapter explains how to mount and connect the Access Point. Depending on your application, you might want to set up the IP address of the device first before mounting the device. Refer to "Chapter 5: Quick Configuration Overview". Personal Installation This product should be installed by a qualified installation professional with RF and related rule knowledge. General users should not attempt to install this product or modify the settings. Installation Location The product should be installed in a location where the radiating antenna is at least 20 cm from anyone under normal operating conditions. This is required to meet regulatory RF exposure requirements. External Antenna Use only antennas approved by Linksys. Antennas that have not been approved by Linksys may produce unwanted spurious or excessive RF transmitting power, this may lead to violation of FCC limitations and is prohibited. Installation Procedure Follow the Hardware Installation instructions for details on installing this product. WARNING: Please carefully select the installation position and make sure that the final output power does not exceed the limit defined in US Rule CFR 47 Part 15, section 15.247 and 15.407. Violation of the rule could lead to serious federal penalties. Hardware Installation 1. Locate an optimum location on a wall for the Access Point. Refer to the antenna pattern in "Chapter 3: Product Overview" to adjust the angle of the Access Point for your application. Wireless-G Exterior Access Point with Power Over Ethernet 2. Using the mounting plate as a template, mark the locations of the two wall-mount slots that are on the bottom of the mounting plate. Then, install a screw into each location. Mark the Locations of the Two Wall-Mount Slots 3. Use four screws (included with the Access Point) to attach the mounting plate to the back panel of the Access Point. Attach the Mounting Plate 4. Connect the included Category 5e Ethernet network cable to the Ethernet network port of the Access Point. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
·
Installation
W±reless-G Exter±or Access Po±nt w±th Power Over Ethernet
Chapter µ
Chapter µ:
Installat±on
Overview
This chapter explains how to mount and connect the
Access Point.
Depending on your application, you might want to set
up the IP address of the device first before mounting
the device. Refer to “Chapter 5: Quick Configuration
Overview”.
Personal Installation
This product should be installed by a qualified installation
professional with RF and related rule knowledge.
General
users should not attempt to install this product or modify
the settings.
Installation Location
The product should be installed in a location where the
radiating antenna is at least 20 cm from anyone under
normal operating conditions. This is required to meet
regulatory RF exposure requirements.
External Antenna
Use only antennas approved by Linksys. Antennas that have
not been approved by Linksys may produce unwanted
spurious or excessive RF transmitting power, this may lead
to violation of FCC limitations and is prohibited.
Installation Procedure
Follow the Hardware Installation instructions for details
on installing this product.
WARNING:
Please
carefully
select
the
installation position and make sure that the
final output power does not exceed the limit
defined in US Rule CFR 47 Part 15, section
15.247 and 15.407. Violation of the rule could
lead to serious federal penalties.
Hardware Installation
Locate an optimum location on a wall for the Access
Point. Refer to the antenna pattern in “Chapter 3:
Product Overview” to adjust the angle of the Access
Point for your application.
1.
Using the mounting plate as a template, mark the
locations of the two wall-mount slots that are on the
bottom of the mounting plate. Then, install a screw
into each location.
Mark the Locations of the Two Wall-Mount Slots
Use four screws (included with the Access Point) to
attach the mounting plate to the back panel of the
Access Point.
Attach the Mounting Plate
Connect the included Category 5e Ethernet network
cable to the Ethernet network port of the Access Point.
2.
3.
4.