Cisco WS-C4003-RF Hardware Maintenance Manual - Page 80

Making Final Connections to the Router, See

Get Cisco WS-C4003-RF - Catalyst 4003 Switch PDF manuals and user guides View all Cisco WS-C4003-RF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Making Final Connections to the Router Making Final Connections to the Router Warning Never operate the router unless the unit is completely closed. This ensures both your safety and adequate cooling. Follow this procedure to make the final connections to the router: Step 1 For routers with AC power input, plug the system power cord into a 3-terminal, single-phase power source that provides power within the acceptable range (200W, 85 to 264 VAC, 50 to 60 Hz). For routers with DC power input, wire the power supply as shown in Figure 3-15. Step 2 Turn ON the system power switch. The LED on the front marked Power should light. (See Figure 1-1.) Step 3 Verify that the OK light located on the right side of the front panel (see Figure 1-1) goes ON after a few seconds delay. Your configuration can be designated with either the setup command facility or with the configuration command. For more information on software commands, refer to the appropriate software publications. 3-22 Cisco 4000 Series Hardware Installation and Maintenance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
3-22
Cisco 4000 Series Hardware Installation and Maintenance
Making Final Connections to the Router
Making Final Connections to the Router
Warning
Never operate the router unless the unit is completely closed. This ensures both your
safety and adequate cooling.
Follow this procedure to make the final connections to the router:
Step 1
For routers with AC power input, plug the system power cord into a 3-terminal,
single-phase power source that provides power within the acceptable range (
200W, 85 to 264
VAC, 50 to 60 Hz). F
or routers with
DC power input, wire the power supply as shown in
Figure 3-15
.
Step 2
Turn ON the system power switch. The LED on the front marked
Power
should light.
(See Figure 1-1.)
Step 3
Verify that the OK light located on the right side of the front panel (see Figure 1-1) goes
ON after a few seconds delay.
Your configuration can be designated with either the
setup
command facility or with the
configuration
command. For more information on software commands, refer to the appropriate
software publications.