Compaq Presario CQ45-100 Compaq Presario CQ45 Notebook PC - Maintenance and Se - Page 90

system board and installed on the replacement system board

Get Compaq Presario CQ45-100 - Notebook PC PDF manuals and user guides View all Compaq Presario CQ45-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

6. Release the system board by sliding it to the right at an angle (3) until the connectors on the left side of the system board disengage from the base enclosure, and then remove the system board. 7. If it is necessary to replace the modem module cable, remove the RJ-11 connector (1) from the clip built into the base enclosure. 8. Remove the modem module cable (2) from the routing channel built into the base enclosure. The modem module cable is available using spare part number 494981-001. When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Fan/heat sink assembly (see Fan/heat sink assembly on page 83) ● Processor (see Processor on page 86) Reverse the preceding procedure to install the system board. 82 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
6.
Release the system board by sliding it to the right at an angle
(3)
until the connectors on the left
side of the system board disengage from the base enclosure, and then remove the system board.
7.
If it is necessary to replace the modem module cable, remove the RJ-11 connector
(1)
from the
clip built into the base enclosure.
8.
Remove the modem module cable
(2)
from the routing channel built into the base enclosure. The
modem module cable is available using spare part number 494981-001.
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
83
)
●
Processor (see
Processor
on page
86
)
Reverse the preceding procedure to install the system board.
82
Chapter 4
Removal and replacement procedures