Compaq ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 35

Ultra2 Hot-Plug Drive Cage, Pull the drive cage partially out of the chassis to access the cables.

Get Compaq ProLiant 3000 PDF manuals and user guides View all Compaq ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2-22 Removal and Replacement Procedures Ultra2 Hot-Plug Drive Cage To remove the Ultra2 hot-plug drive cage assembly: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the front bezel door (tower model only). See "Front Bezel Door" earlier in this chapter. 3. Remove the side access panel. See "Side Access Panel" earlier in this chapter. NOTE: The front fans rest against the drive cage assembly and may cause resistance when the assembly is moved. 4. Remove the front fans. See "Front Fan(s)" earlier in this chapter. 5. Loosen the two thumbscrews securing the drive cage to the chassis 1. 6. Pull out the latch securing the drive cage assembly in the chassis 2. 7. Pull the drive cage partially out of the chassis to access the cables. 8. Disconnect the hard drive backplane power cable, any SCSI cables, and the IDE CD-ROM signal cable. 9. Slide the drive cage assembly out the front of the chassis 3. 1 3 1 2 1 Figure 2-18. Removing the Ultra2 hot-plug drive cage assembly Reverse steps 1 through 9 to replace the Ultra2 hot-plug drive cage assembly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
2-22
Removal and Replacement Procedures
Ultra2 Hot-Plug Drive Cage
To remove the Ultra2 hot-plug drive cage assembly:
1.
Perform the preparation procedures. See “Preparation Procedures” earlier in this chapter.
2.
Remove the front bezel door (tower model only). See “Front Bezel Door” earlier in
this chapter.
3.
Remove the side access panel. See “Side Access Panel” earlier in this chapter.
NOTE
:
The front fans rest against the drive cage assembly and may cause resistance when the
assembly is moved.
4.
Remove the front fans. See “Front Fan(s)” earlier in this chapter.
5.
Loosen the two thumbscrews securing the drive cage to the chassis
1
.
6.
Pull out the latch securing the drive cage assembly in the chassis
2
.
7.
Pull the drive cage partially out of the chassis to access the cables.
8.
Disconnect the hard drive backplane power cable, any SCSI cables, and the
IDE CD-ROM signal cable.
9.
Slide the drive cage assembly out the front of the chassis
3
.
3
1
1
1
2
Figure 2-18. Removing the Ultra2 hot-plug drive cage assembly
Reverse steps 1 through 9 to replace the Ultra2 hot-plug drive cage assembly.