Compaq ProLiant CL1850 Compaq ProLiant CL1850 Software User Guide - Page 15

Manual Installation Using SmartStart

Get Compaq ProLiant CL1850 PDF manuals and user guides View all Compaq ProLiant CL1850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

System Setup and Configuration for Microsoft Windows NT S/E 4.0 1-5 11. At the end of the Windows NT installation, you have the option to view the Error Log. You may view the log by clicking on Yes. When you select No, the system reboots. 12. Log on to Windows NT. 13. If you elected to install Compaq Insight Agents, a configuration screen will appear. Configure the Agents as needed. 14. A prompt to load Service Pack 3 appears. Insert the Windows NT 4.0, Enterprise Edition CD #1 and click OK. When the Confirm File Replace window appears, select No To All. 15. After Service Pack 3 is loaded, remove the CD and click OK. The system reboots. NOTE: It is only necessary to configure the shared drives during server node 1 setup. When configuring server node 2, the CR3500 Configuration Utility shows the results of the shared drives configured during server node 1 setup. 16. At the Enterprise Edition Installer, install Microsoft Cluster Server Administrator. Refer to MSCS documentation for installation steps. 17. After installing MSCS, install the latest Service Pack if applicable. 18. To ensure that the latest Compaq drivers have not been overwritten by the service pack, rerun the Server Support Software. Manual Installation Using SmartStart Performing a manual installation with SmartStart minimizes SmartStart's involvement. The manual installation routine runs Compaq's System Configuration Utility. When you are prompted for the Microsoft Windows NT Server 4.0, Enterprise Edition CD, SmartStart transfers the installation procedure to Windows NT. Follow the instructions on the Windows NT installation screens. To perform a manual installation of cluster software using SmartStart, you need the following: s Compaq SmartStart 4.40 or later s Microsoft Windows NT Server 4.0, Enterprise Edition s SmartStart installation poster

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
System Setup and Configuration for Microsoft Windows NT S/E 4.0
1-5
11.
At the end of the Windows NT installation, you have the option to view
the Error Log. You may view the log by clicking on Yes. When you
select No, the system reboots.
12.
Log on to Windows NT.
13.
If you elected to install Compaq Insight Agents, a configuration screen
will appear. Configure the Agents as needed.
14.
A prompt to load Service Pack 3 appears. Insert the Windows NT 4.0,
Enterprise Edition CD #1 and click OK. When the Confirm File Replace
window appears, select No To All.
15.
After Service Pack 3 is loaded, remove the CD and click OK. The
system reboots.
NOTE:
It is only necessary to configure the shared drives during server node 1 setup.
When configuring server node 2, the CR3500 Configuration Utility shows the results of the
shared drives configured during server node 1 setup.
16.
At the Enterprise Edition Installer, install Microsoft Cluster Server
Administrator. Refer to MSCS documentation for installation steps.
17.
After installing MSCS, install the latest Service Pack if applicable.
18.
To ensure that the latest Compaq drivers have not been overwritten by
the service pack, rerun the Server Support Software.
Manual Installation Using SmartStart
Performing a manual installation with SmartStart minimizes SmartStart’s
involvement. The manual installation routine runs Compaq’s System
Configuration Utility. When you are prompted for the Microsoft Windows NT
Server 4.0, Enterprise Edition CD, SmartStart transfers the installation
procedure to Windows NT. Follow the instructions on the Windows NT
installation screens.
To perform a manual installation of cluster software using SmartStart, you
need the following:
■
Compaq SmartStart 4.40 or later
■
Microsoft Windows NT Server 4.0, Enterprise Edition
■
SmartStart installation poster