Cub Cadet 3X 26 inch TRAC Operation Manual - Page 11

Overhead Chute Rotation Control w/ 4-Way, Electric Pitch & Rotation Control

Get Cub Cadet 3X 26 inch TRAC PDF manuals and user guides View all Cub Cadet 3X 26 inch TRAC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

ASSEMBLY NOTE: For smoothest operation, cables should all be to the left of the chute control rod. Ferrule a 4. Remove hairpin clip (c) from rear of chute control head (Figure 23). Shift Rod b c b Figure 23 5. Insert flex shaft (b) into rear of chute control head, with hairpin clip (c) removed in Step 4 (Figure 23). 6. Perform one of the following to connect the flex shaft to the chute control rod coupling: • Models with Overhead Rotational - Insert hex end of flex shaft into chute control rod coupling under handle panel (Figure 24). Figure 24 • Models with Electric Chute Control - Insert other end of flex shaft into chute control rod coupling under handle panel. Make sure to line up flat end of rod and flat end of coupler. You may need to rotate rod around until these two surfaces line up (Figure 25 inset). Figure 26 9. Make sure the shift lever on the back of the transmission is rotated downward to the full extent of its rotation (Figure 27). Figure 27 10. Insert ferrule into top hole of shift lever and secure with hairpin clip (c) and washer (d) removed in Step 8 (Figure 26). Ferrule may need to be adjusted up or down. STOP Continue to Set-Up (page 13). Overhead Chute Rotation Control w/ 4-Way Electric Pitch & Rotation Control Chute Assembly Chute Control Rod or Manual Chute Control Rod Figure 25 7. Ensure speed selector is in fastest forward speed. 8. Remove hairpin clip (c) and washer (d) from ferrule on end of shift rod (Figure 26 inset). 11 Figure 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
11
ASSEMBLY
NOTE:
For smoothest operation, cables should all be to the left of
the chute control rod.
4.
Remove hairpin clip (c) from rear of chute control head
(Figure 23).
c
b
Figure 23
5.
Insert flex shaft (b) into rear of chute control head, with
hairpin clip (c) removed in Step 4 (Figure 23).
6.
Perform one of the following to connect the flex shaft to the
chute control rod coupling:
•
Models with Overhead Rotational - Insert hex end of flex
shaft into chute control rod coupling under handle panel
(Figure 24).
Figure 24
•
Models with Electric Chute Control - Insert other end of
flex shaft into chute control rod coupling under handle
panel. Make sure to line up flat end of rod and flat end of
coupler. You may need to rotate rod around until these
two surfaces line up (Figure 25 inset).
Figure 25
7.
Ensure speed selector is in fastest forward speed.
8.
Remove hairpin clip (c) and washer (d) from ferrule on end of
shift rod (Figure 26 inset).
Ferrule
Shift Rod
a
b
Figure 26
9.
Make sure the shift lever on the back of the transmission is
rotated downward to the full extent of its rotation
(Figure 27).
Figure 27
10. Insert ferrule into top hole of shift lever and secure with
hairpin clip (c) and washer (d) removed in Step 8 (Figure 26).
Ferrule may need to be adjusted up or down.
STOP
Continue to Set-Up (page 13).
Overhead Chute Rotation Control w/ 4-Way
Electric Pitch & Rotation Control
Chute Control Rod
or
Manual Chute
Control Rod
Chute Assembly
Figure 28