Cub Cadet CS 202 CS 202 Operator's Manual - Page 1
Cub Cadet CS 202 Manual
View all Cub Cadet CS 202 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
CS202 2-Cycle Trimmer Operator's Manual English - Page 1 Removing Unit From Carton Assemble The Unit Slot 1 Remove all contents from carton. Assemble The Unit Bracket 2 Slide shield's slot onto mounting bracket. Rotate shield onto shaft. Push square bolt through shield and bracket. Tighten washer and wing nut onto bolt. Knob 3 Remove the protective cap and gray spacer from the upper and lower shafts. Push the attachment into the coupler. Turn the knob clockwise to tighten. Starting The Unit Primer Bulb Min. 6" 4 Loosen the bolt. Move the handle to the location that provides the best grip. Move the handle a minimum of 6 inches away from the shaft grip. Tighten the bolt until the handle is secure. Choke Lever 40:1 5 Mix thoroughly in a separate fuel can: - 3.2 fl. oz. of 2-cycle engine oil - 1 gallon of unleaded gasoline NOTE: Do not mix directly in the unit fuel tank. 6 Place unit on a level surface. Fill fuel tank. 10 X 7 Press primer bulb 10 times, or until fuel is visible 8 Move choke lever to Position 1. Starting The Unit Choke Lever ASSEMBLY TOOLS REQUIRED: • 3/8" Socket Starter Rope Fuel Cap On/ Off Switch D-Handle Rapid-link™ Throttle Control Cutting Head Shield Need Help? Call 1-877-282-8684 DIDN'T START? Repeat the starting instructions. If the unit still fails to start, refer to the operator's manual for additional starting and troubleshooting information. Choke Lever Français - Page 6 19 Crouch in starting position. 10 SQUEEZE and HOLD throttle for ALL further steps. 5 X 11 Pull rope 5 times. Reloading The Line* Bump Knob Outer Spool 12 Move choke lever to Position 2 and squeeze throttle. 3-5 X 13 Pull rope 3-5 times to start engine. Run unit for 30-60 seconds to warm up. 14 Continue to squeeze throttle. Move choke lever to Position 3. 15 Continue to squeeze throttle. Run unit for an additional 60 seconds to complete warm-up. Unit may be used during this time. Español - Page 11 1 Unscrew the bump knob counterclockwise. Spring 2 Inner Reel Remove the inner reel and spring. 3 Cut one 6-foot (1.8 m) length of new 0.095" split line trimming line. Split each end about 6 inches (150 mm). Top Hole Bottom Hole 4 Insert the end of one line into the top hole and the end of the other line into the bottom hole. Reloading The Line 18 Hold the inner reel and outer spool together. Firmly pull the two line ends to release them from the holding slots. Screw the bump knob on clockwise. Tighten the bump knob securely. For replacement line, call 1-877-282-8684 or go to an authorized service dealer. For single line installation or replacement spool installation instructions, refer to the Replacing the Trimming Line section of this manual. *This is to assist in the reloading of Splitline® only. These instructions are NOT part of the fast assembly instructions. Line does not need to be installed on the initial assembly and start-up. Split Wall 5 Wind the line tightly in the direction shown on the inner reel. The split wall will divide the line. Wind the line until it is completely divided and about 6 inches (150 mm) of line remains. Holding Slots 6 Insert the two 6-inch sections into the two .095 holding slots. Eyelets 7 Pass the two line ends through the eyelets. Place the spring inside the inner reel. Insert the inner reel into the outer spool. Push the inner reel and outer spool together. IMPORTANT: READ THE OPERATOR'S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT. NEED HELP? CALL 1-877-282-8684 IN U.S. OR 1-800-668-1238 IN CANADA 769-07498 P01 03/12