D-Link DCS-4605EV User Manual - Page 16

Using the DCS-37-3 Mount (optional

Get D-Link DCS-4605EV PDF manuals and user guides View all D-Link DCS-4605EV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Section 2: Installation Using the DCS-37-3 Mount (optional) To mount the camera with the DCS-37-3 mount, follow the instructions below. Step 1 Place the DCS-37-3 mounting sticker in the desired location, then use a 6 mm drill bit to drill the required holes 25 mm deep and insert the wall anchors into the holes. If you plan to pass cables through the ceiling, you will also need to drill a hole for the cable channel. Note: The camera in the corresponding graphics may be different from your product, but the procedure is the same. Step 2 Use the provided screws to mount the DCS-37-3 to the ceiling using the inner mounting holes. Step 3 Remove the cover from the camera. Guide the camera connectors through the bottom cable channel on the DCS-37-3. Use the provided screws to mount the camera to the DCS-37-3 using the set of mounting holes marked D. Step 4 Remove the cover and adjust the angle and rotation of the camera as desired, then put the cover back in place. Screw the camera cover back in place. Make sure the rubber stopper is in the side cable channel to seal it. D-Link DCS-4605EV User Manual 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
16
D-Link DCS-4605EV User Manual
Section 2: Installation
Using the DCS-37-3 Mount (optional)
To mount the camera with the DCS-37-3 mount, follow the instructions below.
Step 2
Use the provided screws to mount the DCS-37-3 to the ceiling using the inner mounting holes.
Step 1
Place the DCS-37-3 mounting sticker in the desired location, then use a 6 mm drill bit to drill
the required holes 25 mm deep and insert the wall anchors into the holes. If you plan to pass
cables through the ceiling, you will also need to drill a hole for the cable channel.
Note:
The camera in the corresponding graphics may be diļ¬€erent from your product, but the
procedure is the same.
Step 3
Remove the cover from the camera.
Guide the camera connectors through the bottom cable channel on the DCS-37-3. Use the
provided screws to mount the camera to the DCS-37-3 using the set of mounting holes marked
D
.
Step 4
Remove the cover and adjust the angle and rotation of the camera as desired, then put the
cover back in place. Screw the camera cover back in place.
Make sure the rubber stopper is in the side cable channel to seal it.