Home » D-Link Manuals » Hubs & Switches » D-Link DES-3528 » Manual Viewer

D-Link DES-3528 Product Manual - Page 336

sFlow Counter Poller Settings, sFlow Counter Poller Settings window

UPC - 790069314346

Add to My Manuals
Save this manual to your list of manuals

Page 336 highlights

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide NOTE: If the user wants the change the analyze server ID, he needs to delete the flow sampler and creates a new one. Figure 11-21 sFlow Flow Sampler Settings window The fields that can be configured are described below: Parameter Description Unit Select a unit to configure. From Port / To Port Use the drop-down menus to specify the list of ports to be configured. Analyzer Server ID (1- The analyzer server ID specifies the ID of a server analyzer where the packet will be 4) forwarded. Rate (0-65535) The sampling rate for packet RX sampling. The configured rate value multiplied by 256 is the actual rate. For example, if the rate is 20, the actual rate 5120. One packet will be sampled from every 5120 packets. If set to 0, the sampler is disabled. If the rate is not specified, its default value is 0. Max Header Size (18256) The maximum number of leading bytes in the packet which has been sampled that will be encapsulated and forwarded to the server. If not specified, the default value is 128. Click the Apply button to accept the changes made. Click the Delete All button to remove all the entries listed. Click the Edit button to re-configure the specific entry. Click the Delete button to remove the specific entry. sFlow Counter Poller Settings This window is used to configure the sFlow counter poller parameters. If the user wants the change the analyzer server ID, he needs to delete the counter poller and create a new one. Figure 11-22 sFlow Counter Poller Settings window The fields that can be configured are described below: 327

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

Match case Limit results 1 per page

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

NOTE:

If the user wants the change the analyze server ID, he needs to delete the flow sampler and

creates a new one.

Figure 11-21 sFlow Flow Sampler Settings window

The fields that can be configured are described below:

Parameter

Description

Unit

Select a unit to configure.

From Port / To Port

Use the drop-down menus to specify the list of ports to be configured.

Analyzer Server ID (1-

The analyzer server ID specifies the ID of a server analyzer where the packet will be

forwarded.

Rate (0-65535)

The sampling rate for packet RX sampling. The configured rate value multiplied by 256

is the actual rate. For example, if the rate is 20, the actual rate 5120. One packet will be

sampled from every 5120 packets. If set to 0, the sampler is disabled. If the rate is not

specified, its default value is 0.

Max Header Size (18-

256)

The maximum number of leading bytes in the packet which has been sampled that will

be encapsulated and forwarded to the server. If not specified, the default value is 128.

Click the

Apply

button to accept the changes made.

Click the

Delete All

button to remove all the entries listed.

Click the

Edit

button to re-configure the specific entry.

Click the

Delete

button to remove the specific entry.

sFlow Counter Poller Settings

This window is used to configure the sFlow counter poller parameters. If the user wants the change the analyzer server

ID, he needs to delete the counter poller and create a new one.

Figure 11-22 sFlow Counter Poller Settings window

The fields that can be configured are described below:

327