D-Link DFE-2616X User Guide - Page 60

Software Update on Boot

Get D-Link DFE-2616X - Hub - Stackable PDF manuals and user guides
UPC - 790069212604
View all D-Link DFE-2616X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Dual-Speed Stackable Hubs User's Guide DFE-2600 Stackable Hub - Out-of-Band/Console Setting Menu Out-of-Band Setting Console Setting: Protocol: Baud Rate: Character Size: Stop Bit: SLIP 9600 8 1 Baud Rate: Character Size: Stop Bit: 9600 8 1 System Restart Out-of-Band Baud Rate Out-of-Band Dial Up Phone Number [ ] Current Serial Port Setting: Console System Restart Serial Port Setting HELP SAVE EXIT Software Update on Boot The hub is capable of obtaining its boot-time configuration information, as well as updated versions of its internal firmware, using TFTP (the Trivial File Transfer Protocol) and BOOTP (the BOOTstrap Protocol). You can use the Software Update menu to control this feature. The fields you can set on this menu are: ♦ Software Update. This parameter determines whether or not the hub will try to look for the configuration file over the network. If set to Disable, the parameters below become irrelevant. ♦ Software Update Mode. This variable can be set to either Network or Out-of-band. Determines whether the configuration file should be obtained through the Ethernet network or through the console port. ♦ Boot Protocol. This parameter can be set to either TFTP ONLY or BOOTP&TFTP. Applies only if the S/W Update control is enabled. 48 Master Hub Setup and Management

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Dual-Speed Stackable Hubs User’s Guide
Master Hub Setup and Management
48
DFE-2600 Stackable Hub - Out-of-Band/Console Setting Menu
Out-of-Band Setting
Console Setting:
Protocol:
SLIP
Baud Rate:
9600
Baud Rate:
9600
Character Size:
8
Character Size:
8
Stop Bit:
1
Stop Bit:
1
System Restart Out-of-Band Baud Rate
<9600 >
Out-of-Band Dial Up Phone Number
[
]
Current Serial Port Setting:
Console
System Restart Serial Port Setting <Console
>
HELP
SAVE
EXIT
Software Update on Boot
The hub is capable of obtaining its boot-time configuration information, as
well as updated versions of its internal firmware, using TFTP (the Trivial File
Transfer Protocol) and BOOTP (the BOOTstrap Protocol).
You can use the
Software Update menu to control this feature.
The fields you can set on this menu are:
♦
Software Update
.
This parameter determines whether or not the hub
will try to look for the configuration file over the network.
If set to
Disable, the parameters below become irrelevant.
♦
Software Update Mode
.
This variable can be set to either Network
or Out-of-band.
Determines whether the configuration file should be
obtained through the Ethernet network or through the console port.
♦
Boot Protocol
.
This parameter can be set to either TFTP ONLY or
BOOTP&TFTP.
Applies only if the
S/W Update
control is enabled.