D-Link DGS-1210-10P Product Manual - Page 65

Command Line Interface, To connect a switch via TELNET: - cli

Get D-Link DGS-1210-10P PDF manuals and user guides
UPC - 790069329388
View all D-Link DGS-1210-10P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

6 Command Line Interface D-Link Web Smart Switch User Manual 6 Command Line Interface The D-Link Web Smart Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol. To connect a switch via TELNET: 1. Make sure the network connection between the switch and PC is active. 2. To connect, launch any terminal software like HyperTerminal in Microsoft Windows, or just use the command prompt by typing the command telnet followed by the switch IP address, eg. telnet 10.90.90.90. 3. The logon prompt will appear. Logging on to the Command Line Interface: Enter your User Name and Password to log in. The default user name and password is admin. Note that the user name and password are case-sensitive. Press Enter in both the Username and Password fields. The command prompt will appear as shown below (DGS-1210-10P>): Figure 98 - Command Prompt The user session is automatically terminated if idle for the login timeout period. The default login timeout period is 5 minutes. To change the login timeout session, please refer to chapter 5. CLI Commands: There are a number of helpful features included in the CLI. Entering the ? command will display a list of commands. Figure 99 - The ? Command Download The download command is used to download and install new firmware or a Switch configuration file from a TFTP server. Syntax download { firmware_fromTFTP tftp://ip-address/filename | cfg_fromTFTP tftp://ip-address/filename} Parameters Parameter Description 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
6
Command
Line Interface
D-Link Web Smart Switch User Manual
6
Command Line Interface
The D-Link Web Smart Switch allows a computer or terminal to perform some basic monitoring and
configuration tasks by using the Command Line Interface (CLI) via TELNET protocol.
To connect a switch via TELNET:
1. Make sure the network connection between the switch and PC is active.
2. To connect, launch any terminal software like
HyperTerminal
in Microsoft Windows, or just use the
command prompt by typing the command
telnet
followed by the switch IP address, eg.
telnet 10.90.90.90
.
3. The logon prompt will appear.
Logging on to the Command Line Interface:
Enter your User Name and Password to log in. The default user name and password is
admin
. Note that the
user name and password are case-sensitive. Press
Enter
in both the Username and Password fields. The
command prompt will appear as shown below (
DGS-1210-10P>):
Figure 98 – Command Prompt
The user session is automatically terminated if idle for the login timeout period. The default login timeout
period is 5 minutes. To change the login timeout session, please refer to chapter 5.
CLI Commands:
There are a number of helpful features included in the CLI. Entering the
?
command will display a list of
commands.
Figure 99 – The ? Command
Download
The
download
command is used to download and install new firmware or a Switch configuration file
from a TFTP server.
Syntax
download
{ firmware_fromTFTP tftp://ip-address/filename | cfg_fromTFTP
tftp://ip-address/filename}
Parameters
Parameter
Description
59