D-Link DGS-1210-24 Product Manual
D-Link DGS-1210-24 Manual
 |
UPC - 790069332296
View all D-Link DGS-1210-24 manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DGS-1210-24 manual content summary:
- D-Link DGS-1210-24 | Product Manual - Page 1
- D-Link DGS-1210-24 | Product Manual - Page 2
D-Link Web Smart Switch User Manual Table of Contents Table of Contents ...i About This Guide...1 Terms/Usage...1 Copyright and Trademarks ...1 Product Introduction ...2 DGS-1210-16 ...3 Front Panel ...3 Rear Panel...3 DGS-1210-24 ...3 Front Panel ...3 Rear Panel...4 DGS-1210-48 ...4 Front - D-Link DGS-1210-24 | Product Manual - Page 3
Table of Contents D-Link Web Smart Switch User Manual Save Configuration ...23 Save Log ...23 Tool Bar > Tool Menu ...23 Reset ...23 Reset System ...23 Reboot Device ...24 Configuration Backup & Restore ...24 Firmware Backup and Upload ...24 Tool Bar > Smart Wizard...25 Tool Bar > Online Help...25 - D-Link DGS-1210-24 | Product Manual - Page 4
Table of Contents D-Link Web Smart Switch User Manual Command Line Interface...59 To connect a switch via TELNET:...59 Logging on to the Command Line Interface 59 CLI Commands: ...59 Download...59 Upload ...60 Config ipif System...60 Logout...60 Ping ...61 Reboot ...61 Reset ...61 Show ipif ...61 - D-Link DGS-1210-24 | Product Manual - Page 5
About This Guide D-Link Web Smart Switch User Manual About This Guide This guide provides instructions to install the D-Link Gigabit Web Smart Switch DGS-1210-16/24/48, how to use the SmartConsole Utility, and to configure Web-based Management step-by-step. Note: The model you have purchased may - D-Link DGS-1210-24 | Product Manual - Page 6
extensive switch configuration settings, and basic configuration of discovered devices, such as a password change or firmware upgrade. Users can also access the switch via TELNET. Some basic tasks can be performed such as changing the Switch IP address, resetting the settings to factory defaults - D-Link DGS-1210-24 | Product Manual - Page 7
the Reset button, the Switch will change back to the default configuration and all changes will be lost. Rear Panel Figure 2 - DGS-1210-16 Rear Panel Power: The power port is where to connect the AC power cord. DGS-1210-24 24-Port 10/100/1000Mbps with 4 Combo SFP Slot Web Smart Switch Front - D-Link DGS-1210-24 | Product Manual - Page 8
link up, the RJ-45 port cannot be used. Rear Panel CAUTION: The MiniGBIC ports should use UL listed optical transceiver product. Figure 4 - DGS-1210-24 Rear Panel Power: Connect the supplied AC power cable to this port. DGS-1210-48 48-Port 10/100/1000Mbps with 4 Combo SFP Slot Web Smart Switch - D-Link DGS-1210-24 | Product Manual - Page 9
1 Product Introduction D-Link Web Smart Switch User Manual Rear Panel Figure 6 - DGS-1210-48 Rear Panel Power: Connect the supplied AC power cable to this port. 5 - D-Link DGS-1210-24 | Product Manual - Page 10
is missing or damaged, please contact your local D-Link reseller for replacement. One D-Link Web-Smart Switch One AC power cord Four rubber feet Screws and two mounting brackets One Multi-lingual Getting Started Guide One CD with User Manual, SmartConsole Utility program, and D-View Module If any - D-Link DGS-1210-24 | Product Manual - Page 11
Link Web Smart Switch User Manual Then, use the screws provided with the equipment rack to mount the switch in the rack. Figure 9 - Mount the Switch in the rack or chassis Please be aware of following safety Instructions ratings should be used when addressing this concern. E) Reliable Earthing - D-Link DGS-1210-24 | Product Manual - Page 12
2 Hardware Installation D-Link Web Smart Switch User Manual Figure 10 -Plugging the switch into an outlet Power Failure As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in. 8 - D-Link DGS-1210-24 | Product Manual - Page 13
D-Link Web Smart Switches, the SmartConsole Utility is a more convenient choice. By using the SmartConsole Utility, you do not need to change the IP address of your PC and it is easier to initialize multiple Smart Switches. Please refer to the following installation instructions for the Web-based - D-Link DGS-1210-24 | Product Manual - Page 14
D-Link Web Smart Switch User Manual Login Web-based Management In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have an IP address of 10 - D-Link DGS-1210-24 | Product Manual - Page 15
3 Getting Started D-Link Web Smart Switch User Manual Option 1: Follow these steps to install the the on-screen instructions to install the utility. 5. Upon completion, go to Start > Programs > D-Link SmartConsole Utility and open the SmartConsole Utility. 6. Connect the Smart Switch to the same - D-Link DGS-1210-24 | Product Manual - Page 16
D-Link Web Smart Switch User Manual 4 SmartConsole Utility The D-Link SmartConsole Utility allows the administrator to quickly discover all D-Link smart switches, which are in the same domain of the PC, collect traps and log messages, and quick access to basic configurations of the switch. The - D-Link DGS-1210-24 | Product Manual - Page 17
4 SmartConsole Utility D-Link Web Smart Switch User Manual Web-Smart Switch will not be discovered. Log Click this icon to launch the Log window. Click View Log to show the events of the SmartConsole Utility and the device. Date/Time indicates when the message was received, IP denotes where it - D-Link DGS-1210-24 | Product Manual - Page 18
Link Web Smart Switch User Manual Figure 18 - SmartConsole File Monitor Save: Records the setting of the Device List as default for the next time the SmartConsole Utility is used. Monitor Save As: Records the setting of the Device List in an appointed filename and file path. Monitor Load: Manually - D-Link DGS-1210-24 | Product Manual - Page 19
D-Link Web Smart Switch User Manual Device Configuration The Device Configuration in the SmartConsole Utility has five icons: Device Settings Device Password Manager Multi Firmware Upgrade DHCP Refresh Web Access and the , , device buttons for the Device List. Device Settings Select a switch - D-Link DGS-1210-24 | Product Manual - Page 20
Utility D-Link Web Smart Switch User Manual Device Password Manager Select a switch from the Device List. Click on this icon to launch the Device Password Manager window. Here you can enter a new password and confirm it. Figure 21 - SmartConsole Device Password Manager Multi Firmware Upgrade - D-Link DGS-1210-24 | Product Manual - Page 21
D-Link Web Smart Switch User Manual Figure 23 - DHCP Refresh Web Access Select a switch from the Device List. Click this icon to launch your Internet browser (eg. The Internet Explorer). Here you can configure the Switch through the Web-based Management utility. You may also get into the Web - D-Link DGS-1210-24 | Product Manual - Page 22
4 SmartConsole Utility D-Link Web Smart Switch User Manual Protocol version: Displays the software version of the Utility. Product Name: Displays the device product name. System Name: Displays the appointed device system name. DHCP: Specify if the device gets the IP address from a DHCP server. - D-Link DGS-1210-24 | Product Manual - Page 23
5 Configuration D-Link Web Smart Switch User Manual 5 Configuration The features and functions of the D-Link Web Smart Switch can be configured for optimum use through the Web-based Management Utility. Smart Wizard Configuration After a successful login, the Smart Wizard will guide you through - D-Link DGS-1210-24 | Product Manual - Page 24
5 Configuration D-Link Web Smart Switch User Manual SNMP Settings The SNMP Setting allows you to quickly enable/disable the SNMP function and configure the SNMP community name. For the complete SNMP function, please check "Setup Menu > System > SNMP Settings" in the Web Interface. The default SNMP - D-Link DGS-1210-24 | Product Manual - Page 25
D-Link Web Smart Switch User Manual System Settings You can manually change the system IP Address, Subnet Mask, and Gateway address by selecting Static and clicking Apply. You can further configure and read more about the above settings in the "Setup Menu > System > System Settings". The default - D-Link DGS-1210-24 | Product Manual - Page 26
5 Configuration D-Link Web Smart Switch User Manual Web-based Management After clicking the Exit button in Smart Wizard you will see the screen below: Tool Bar Function Tree Main Configuration Screen Figure 31 - Web-based Management The above image is the Web-based Management screen. The three - D-Link DGS-1210-24 | Product Manual - Page 27
such as Reset, Reset System, Reboot Device, Configuration Backup and Restore, Firmware Backup and Upgrade. Figure 35 - Tool Menu Reset Provide a safe reset option for the Switch. All configuration settings in non-volatile RAM will be reset to factory default except for the IP address. Figure 36 - D-Link DGS-1210-24 | Product Manual - Page 28
5 Configuration D-Link Web Smart Switch User Manual Figure 37 - Tool Menu > Reset System Reboot Device Provide a safe way to reboot the system. Click Reboot to restart the switch. Figure 38 - Tool Menu > Reboot Device Configuration Backup & Restore Allow the current configuration settings to be - D-Link DGS-1210-24 | Product Manual - Page 29
5 Configuration D-Link Web Smart Switch User Manual Figure 40 - Tool Menu > Firmware Backup and Upload HTTP: Backup or upgrade the firmware to or from your local PC drive. Click Backup to save the firmware to your disk. Click Browse to browse your inventories for a saved firmware file. Click - D-Link DGS-1210-24 | Product Manual - Page 30
5 Configuration D-Link Web Smart Switch User Manual Figure 42 - User Guide Micro Site 26 - D-Link DGS-1210-24 | Product Manual - Page 31
of the switch, including essential information such as firmware & hardware information, and IP address. It also offers an overall status of common software features: RSTP: Click Setting to link to Configuration > Spanning Tree > STP Global Settings. Default is disabled. Port Mirroring: Click - D-Link DGS-1210-24 | Product Manual - Page 32
5 Configuration D-Link Web Smart Switch User Manual Figure 44 - Device Information System > System Settings The System Setting allows the user to configure the IP address and the basic system information of the Switch. IP Information: There are two ways for the switch to obtain an IP address: - D-Link DGS-1210-24 | Product Manual - Page 33
5 Configuration D-Link Web Smart Switch User Manual System Event: The system level messages, which contains: Device Bootup - System boot-up information. Illegal Login - Events of incorrect password logins, recording the IP of the originating PC. Fiber Port Link Up/Link Down: Fiber port connection - D-Link DGS-1210-24 | Product Manual - Page 34
default SNMP setting is disabled. Click Enabled to set Community Settings and then Apply. Figure 48 - System > SNMP Setting Community Setting: In support of SNMP version 1, the Web-Smart Switch accomplishes user authentication by using Community Settings that function as passwords. The remote user - D-Link DGS-1210-24 | Product Manual - Page 35
up to eight facilities can be assigned (Local 0 ~ Local 7), Configuration > Jumbo Frame D-Link Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1536 bytes) of up to 10,000 bytes (tagged). Default is disabled, Select Enabled then click Apply to turn on - D-Link DGS-1210-24 | Product Manual - Page 36
5 Configuration D-Link Web Smart Switch User Manual Configuration > 802.1Q VLAN A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area. VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups ( - D-Link DGS-1210-24 | Product Manual - Page 37
5 Configuration D-Link Web Smart Switch User Manual Figure 54 - Configuration > 802.1Q VLAN > Example VIDs Figure 55 - Configuration > 802.1Q VLAN > VID Assignments Configuration > Asymmetric VLAN This function is located in the 802.1Q Configuration page. It allows devices in different VLANs to - D-Link DGS-1210-24 | Product Manual - Page 38
5 Configuration D-Link Web Smart Switch User Manual Figure 57 - Configuration > 802.1Q VLAN > Asymmetric VLAN - Enabling Asymmetric VLAN 2. Configure the shared VLAN (VLAN 1) and access VLANs (VLAN 2, 3, 4) In this case, the default VLAN is used as shared VLAN, and the ports that are shared in the - D-Link DGS-1210-24 | Product Manual - Page 39
5 Configuration D-Link Web Smart Switch User Manual After configuration, the user will be able to share the network resources set on the shared group of ports (nominated as PVID 1), with both smaller subsets of VLANs (nominated PVID 2, 3 and 4). However, VLAN 2, 3 and 4 groups are incapable of - D-Link DGS-1210-24 | Product Manual - Page 40
5 Configuration D-Link Web Smart Switch User Manual Aging Time: Enter a period of time (in hours) to remove a port from the voice VLAN if the port is an automatic VLAN member. When the last voice device stops sending traffic and the MAC address of this voice device is aged out, the voice VLAN - D-Link DGS-1210-24 | Product Manual - Page 41
5 Configuration D-Link Web Smart Switch User Manual Select the OUI and press Add to the lower table to complete the Auto Voice VLAN setting. Configuration > Link Aggregation > Port Trunking The Trunking function enables the combining of two or more ports together to increase bandwidth. Up to eight - D-Link DGS-1210-24 | Product Manual - Page 42
5 Configuration D-Link Web Smart Switch User Manual Port Priority (0-65535): Displays the LACP priority value for the port. Default is 128. Activity: There are two different roles of LACP ports: Active - Active LACP ports are capable of processing and sending LACP control frames. This allows LACP - D-Link DGS-1210-24 | Product Manual - Page 43
. Default is 10 seconds. Querier State: D-Link Smart Switch is able to send out the IGMP Queries to check the status of multicast clients. Default is disabled. To enable IGMP snooping for a given VLAN, select enable and click on the Apply button. Then press the Edit button under Router Port Setting - D-Link DGS-1210-24 | Product Manual - Page 44
5 Configuration D-Link Web Smart Switch User Manual Figure 68 - Configuration > Port Mirroring Selection options for the Source Ports are as follows: TX (transmit) mode: Duplicates the data transmitted from the source port and forwards it to the Target Port. Click "all" to include all ports into - D-Link DGS-1210-24 | Product Manual - Page 45
5 Configuration D-Link Web Smart Switch User Manual Figure 70 - Configuration > Loopback Detection Loopback Detection State: Use the drop-down menu to enable or disable loopback detection. The default is Disabled. Interval (1-32767): Set a Loop detection Interval between 1 and 32767 seconds. The - D-Link DGS-1210-24 | Product Manual - Page 46
5 Configuration D-Link Web Smart Switch User Manual Current Time: Displays the current date and time for the switch. If choosing SNTP for the clock source, then the following parameters will be available: SNTP First Server: Specify the IP address of the primary SNTP server from which the system - D-Link DGS-1210-24 | Product Manual - Page 47
Configuration D-Link Web Smart Switch User Manual default is 15 seconds. Root Bridge: Displays the MAC address of the Root Bridge. Root Maximum Age: Displays the Maximum Age of the Root Bridge. Root Forward Delay: Displays the Forward Delay of the Root Bridge. Root port: Displays the root port - D-Link DGS-1210-24 | Product Manual - Page 48
5 Configuration D-Link Web Smart Switch User Manual Configuration > Spanning Tree > STP Port Settings STP can be set up on a port per port basis. In addition to setting Spanning Tree parameters for use on the switch level, the Switch allows for the configuration of the groups of ports, each port- - D-Link DGS-1210-24 | Product Manual - Page 49
D-Link Web Smart Switch User Manual port status. Selecting the False parameter indicates that the port does not have edge port status. Selecting the Auto parameter indicates that the port have edge port status or not have edge port status automatically. Priority: Specify the priority of each port - D-Link DGS-1210-24 | Product Manual - Page 50
Configuration D-Link Web Smart Switch User Manual Figure 76 - QoS > Bandwidth Control From Port / To Port: A consecutive group of ports may be configured starting with the selected port for the selected ports. NOTE: The TX rate for Gigabit ports can only be configured in multiples of 1850kbps - D-Link DGS-1210-24 | Product Manual - Page 51
Switch User Manual Figure 77 - QoS > 802.1p Default Priority By selecting the DSCP priority, the web pages will changes as seen below: Figure 78 - QoS > DSCP Priority Settings Select QoS Mode: D-Link Smart Switch allows the user to prioritize the traffic based on the 802.1p priority in the VLAN - D-Link DGS-1210-24 | Product Manual - Page 52
5 Configuration D-Link Web Smart Switch User Manual Security > Trusted Host Use Trusted Host function to manage the switch from a remote station. You can enter up to ten designated management stations networks by defining the IP address/Subnet Mask as seen in the figure below. Figure 79 Security - D-Link DGS-1210-24 | Product Manual - Page 53
5 Configuration D-Link Web Smart Switch User Manual Figure 81 - Security > Port Security Security > 802.1X > 802.1X Settings Network switches provide easy and open access to resources, by simply attaching a client PC. Unfortunately this automatic configuration also allows unauthorized personnel to - D-Link DGS-1210-24 | Product Manual - Page 54
5 Configuration D-Link Web Smart Switch User Manual TxPeriod (1 - 65535 sec): This sets the TxPeriod of time for the authenticator PAE state machine. This value determines the period of an EAP Request/Identity packet transmitted to the client. Default is 24 seconds. ReAuthEnabled: This function is - D-Link DGS-1210-24 | Product Manual - Page 55
5 Configuration D-Link Web Smart Switch User Manual Figure 83 - Security > Static Mac Address To initiate the removal of auto-learning for any of the uplink ports, click On to enable this feature, and then select the port(s) for auto learning to be disabled. The Static MAC Address Setting table - D-Link DGS-1210-24 | Product Manual - Page 56
Web Smart Switch User Manual To view the statistics of individual ports, click one of the linked port numbers for details. Figure 86 - Monitoring > Port Statistics Previous Page: Go back to the Statistics main page. Refresh: To renew the details collected and displayed. Clear Counter: To reset - D-Link DGS-1210-24 | Product Manual - Page 57
D-Link Web Smart Switch User Manual Monitoring > Cable Diagnostics The Cable Diagnostics is designed primarily for administrators and customer service representatives to examine the copper cable quality. It rapidly determines the type of cable errors occurred in the cable. Select a port and - D-Link DGS-1210-24 | Product Manual - Page 58
5 Configuration D-Link Web Smart Switch User Manual Figure 88 - Monitoring > System Log ID: Displays an Switch will forward packets based on the information contained in each packet's header. This criteria can be specified on a basis of the MAC address, or IP address. The ACL Configuration - D-Link DGS-1210-24 | Product Manual - Page 59
Configuration D-Link Web Smart Switch User Manual Service Type: Specify the type of service. The possible values are: Any - Indicates ACL action will be on packets from any service if all other ACL criteria is met. Port: Enter a range of ports to be configured. Press Apply for the settings to take - D-Link DGS-1210-24 | Product Manual - Page 60
To delete an access profile. To manually add a profile, click Add ACL Profile: D-Link Web Smart Switch User Manual Figure 91 - Add Access Profile The , if you want to check a network of 192.168.1.0/24, then you should enter the IP mask as 255.255.255.0. NOTE: You cannot select Payload in a MAC - D-Link DGS-1210-24 | Product Manual - Page 61
5 Configuration D-Link Web Smart Switch User Manual Profile ID: Indicates the corresponding access profile Identification number. Access ID: Indicates the access rule Identification number. Profile Type: Displays the profile type. Summary: Displays - D-Link DGS-1210-24 | Product Manual - Page 62
5 Configuration D-Link Web Smart Switch User Manual NOTE: The switch begins the access rule with the smallest This page is used to help find a previously configured ACL entry. To search for an entry, enter the profile ID from the drop-down menu, select a port that you wish to view, define the state - D-Link DGS-1210-24 | Product Manual - Page 63
telnet followed by the switch IP address, eg. telnet 10.90.90.90. 3. The logon prompt will appear. Logging on to the Command Line Interface: Enter your User Name and Password to log in. The default user name and password is admin. Note that the user name and password are case-sensitive. Press - D-Link DGS-1210-24 | Product Manual - Page 64
6 Command Line Interface D-Link Web Smart Switch User Manual Parameter firmware_fromTFTP cfg_fromTFTP tftp://ip-address/ filename Description Download and install new firmware on the Switch from a TFTP server. Download a switch configuration file from a TFTP server. The IP address of the TFTP - D-Link DGS-1210-24 | Product Manual - Page 65
Web Smart Switch User Manual NOTE: Save your configuration changes before logging out. Ping This command checks if another computer is on the network and listens for connections. You can ping the switch from any IP workstation the switch is connected to through the managed VLAN (VLAN 1 by default - D-Link DGS-1210-24 | Product Manual - Page 66
Line Interface Example D-Link Web Smart Switch User Manual Figure 99 - The show switch Command Config account admin password The command sets the administrator password. Syntax config account admin password Parameter Parameter Description The new password of the administrator - D-Link DGS-1210-24 | Product Manual - Page 67
D-Link Web Smart Switch User Manual Appendix A - Ethernet Technology This chapter will describe the features of the D-Link Web Smart Switch and provide some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology. Gigabit Ethernet Technology Gigabit Ethernet - D-Link DGS-1210-24 | Product Manual - Page 68
D-Link Web Smart Switch User Manual Appendix B - Technical Specifications Hardware Specifications Key Components / Performance Switching Capacity: - DGS-1210-16: 32Gbps - DGS-1210-24: 48Gbps - DGS-1210-48: 96Gbps Max. Forwarding Rate - DGS-1210-16: 23.8Mpps - DGS-1210-24: 35.7Mpps - DGS-1210-48 - D-Link DGS-1210-24 | Product Manual - Page 69
for destination IP, system events, fiber port events, twisted-pair port events Port access control Web-based configuration backup / restoration Web-based firmware backup/restore Firmware upgrade using SmartConsole Utility & Web-based management Reset, Reboot D-Link Web Smart Switch User Manual 63 - D-Link DGS-1210-24 | Product Manual - Page 70
Instructions D-Link Web Smart Switch User Manual Appendix C - Rack mount Instructions Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions ratings should be used when addressing this concern. E) Reliable - D-Link DGS-1210-24 | Product Manual - Page 71
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
 |
 |
