D-Link DGS-1500-20 User Manual - Page 39

VLAN > GVRP > GVRP Global Settings

Get D-Link DGS-1500-20 PDF manuals and user guides View all D-Link DGS-1500-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

5 Configuration D-Link Web Smart Switch User Manual VLAN > GVRP > GVRP Global Settings The GVRP Global Settings page allows user to configure the GARP timer values for application join, leave, and leave_all GARP timer values. Figure 5.31 - VLAN > GVRP > GVRP Global Settings GVRP: Disabled or Enabled the GVRP status. Join Time (100-100000): Indicates the time in milliseconds that PDUs are transmitted. The default value is 200ms. Leave Time (100-100000): Indicates the amount of time in milliseconds that the device waits before leaving its GARP state. The leave time is activated by a leave all time message sent/received, and cancelled by the Join message. The default value is 600ms. Leave_All Time (100-100000): Used to confirm the port within the VLAN. The time in milliseconds between messages sent. The default value is 10000ms. Click Apply to implement changes made. NOTE: Leave time must be greater than or equal to three times the join time. Leave_all time must be greater than the leave time. VLAN > GVRP > GVRP Port Settings The GVRP Port Settings page allows user to determine whether the Switch will share its VLAN configuration information with other GARP VLAN Registration Protocol (GVRP) enabled switches. In addition, Ingress Checking can be used to limit traffic by filtering incoming packets whose PVID does not match the PVID of the port. Results can be seen in the table under the configuration settings, as seen below. Figure 5.32 - VLAN > GVRP > GVRP Port Settings 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
5
Configuration
D-Link Web Smart Switch User Manual
34
VLAN > GVRP > GVRP Global Settings
The GVRP Global Settings page allows user to configure the GARP timer values for application join, leave,
and leave_all GARP timer values.
Figure 5.31 – VLAN > GVRP > GVRP Global Settings
GVRP:
Disabled or Enabled the GVRP status.
Join Time (100-100000):
Indicates the time in milliseconds that PDUs are transmitted. The default value is
200ms
.
Leave Time (100-100000):
Indicates the amount of time in milliseconds that the device waits before leaving
its GARP state. The leave time is activated by a leave all time message sent/received, and cancelled by the
Join message. The default value is
600ms
.
Leave_All Time (100-100000):
Used to confirm the port within the VLAN. The time in milliseconds between
messages sent. The default value is
10000ms
.
Click
Apply
to implement changes made.
NOTE:
Leave time must be greater than or equal
to three times the join time.
Leave_all time must be greater than the
leave time.
VLAN > GVRP > GVRP Port Settings
The GVRP Port Settings page allows user to determine whether the Switch will share its VLAN configuration
information with other
GARP VLAN Registration Protocol (GVRP)
enabled switches. In addition, Ingress
Checking can be used to limit traffic by filtering incoming packets whose PVID does not match the PVID of
the port. Results can be seen in the table under the configuration settings, as seen below.
Figure 5.32 – VLAN > GVRP > GVRP Port Settings