D-Link DWL-650 Product Manual - Page 17

Configuration, Maximum Power Save - manual

Get D-Link DWL-650 - DI 713p Wireless Router PDF manuals and user guides
UPC - 790069235740
View all D-Link DWL-650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Configuration Utility Configuration To communicate on the network, all devices must have the same settings for the following properties: This Configuration screen displays the default settings for the DWL-650+. SSID - (Service Set Identifier) is a name that identifies a wireless network. Access Points and wireless clients attempting to connect to a specific WLAN (Wireless Local Area Network) must use the same SSID. The default setting is default. Wireless Mode - Click on the pull-down menu; select from the following options: Infrastructure - connecting the WLAN using an Access Point such as the DWL-1000AP. (The default setting.) Ad-Hoc - wireless mode used when connecting directly to a computer equipped with a wireless adapter such as the D-Link AirPlus DWL-520 Wireless PCI adapter in a peer-to-peer environment. Channel - The default channel setting is channel 6. However, the DWL-650+ will automatically select the channel to match the channel setting for the selected Access Point. In Ad Hoc mode, the channel must be manually set to the same channel for each wireless adapter. TX Rate - Select the transmission rate on the network. 11Mbps is the default setting. Preamble - Select Long or Short Preamble. The Preamble defines the length of the CRC block (Cyclic Redundancy Check is a common technique for detecting data transmission errors) for communication between the Access Point and the roaming wireless Network adapters. Long Preamble is the default setting. Note: High network traffic areas should use the shorter preamble type. Power Mode - Select from three modes: Continuous Access Mode-this default setting consumes the most power Maximum Power Save-this setting consumes the least power Power Save- this setting consumes a moderate amount of power 4x Config - Select 4x Disable or 4x Enable. The 4x feature increases your data throughput when 4x is enabled on both the wireless client and either the DWL900AP+ (wireless Access Point) or the DI-614+ (wireless Router.) Click Apply to save the changes. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
17
Configuration Utility
Configuration
SSID -
(Service Set Identifier) is a name that identifies a wireless network.
Access
Points and wireless clients attempting to connect to a specific WLAN (Wireless Local
Area Network) must use the same SSID.
The default setting is
default
.
Wireless Mode
- Click on the pull-down menu; select from the following options:
Infrastructure
- connecting the WLAN using an Access Point such as the
DWL-1000AP.
(The
default
setting.)
Ad-Hoc –
wireless mode used when connecting directly to a computer
equipped with a wireless adapter such as the D-Link
Air
Plus DWL-520
Wireless PCI adapter in a peer-to-peer environment.
Channel –
The
default
channel setting is channel 6.
However, the DWL-650+ will
automatically select the channel to match the channel setting for the selected
Access Point. In Ad Hoc mode, the channel must be manually set to the same
channel for each wireless adapter.
TX Rate
- Select the transmission rate on the network. 11Mbps is the
default
setting.
Preamble
- Select
Long
or
Short
Preamble.
The Preamble defines the length of
the CRC block (Cyclic Redundancy Check is a common technique for detecting data
transmission errors) for communication between the Access Point and the roaming
wireless Network adapters.
Long Preamble
is the
default
setting
.
Note:
High
network traffic areas should use the shorter preamble type.
Power Mode
– Select from three modes:
Continuous Access Mode-
this
default
setting consumes the most power
Maximum Power Save
-this setting consumes the least power
Power Save-
this setting consumes a moderate amount of power
4x Config –
Select
4x Disable
or
4x Enable.
The 4x feature increases your data
throughput when 4x is enabled on both the wireless client and either the DWL-
900AP+ (wireless Access Point) or the DI-614+ (wireless Router.)
Click
Apply
to save the changes
.
This Configuration
screen displays the
default settings for
the DWL-650+.
To communicate on the network, all devices must have
the same settings for the following properties: