Dacor ER30DSR Installation Instructions - Page 10

Planning the Installation Cabinet Layout (continued) APPROVED RAISED VENT MODELS: Use only Dacor model ERV30 or PRV30. Non-combustible rear wall recommeded 10" Min. (254 mm) both sides 1/4" Min. (6 mm) Countertop overhang Non-combustible rear wall recommended 10" Min. (254 mm) both sides 3/8" Min. (10 mm) Countertop overhang Combustible side wall above range 29 1/2" (749 mm) countertop opening 30" (762 mm) cabinet opening below countertop HJK Cabinet face below countertop Notch countertop overhang to width of cabinets Countertop front Countertop Height: Min: 35 5/8" (905 mm) Max: 37 3/8" (949 mm) 27 1/2" (699 mm) raised vent opening 29 1/2" (749 mm) countertop opening 30" (762 mm) cabinet opening below countertop 2 3/8" (60 mm) HJK Combustible side wall above range Cabinet face below countertop Notch countertop overhang to width of cabinets Countertop front Countertop Height: Min: 35 5/8" (905 mm) Max: 37 1/4" (946 mm) Top View - Model ER30DSR - Counter/Cabinet Cutout Dimensions for Self-Rimming Installation Top View - Model ER30DSR - Counter/Cabinet Cutout Dimensions - Self-Rimming Installation with Raised Vent Notes For All Self-Rimming Installations: • On installations without a raised vent (see above), when sliding the range into position, it will stop when the rear of the control panel contacts the notches toward the front of the countertop. The range trim will partially cover the overhang in back. • On installations with a raised vent (see above right), install Dacor trim kit ATK30SR. When sliding the range into position, it will stop when the rear of the control panel contacts the notches toward the front of the countertop. The range trim will partially cover the front of the raised vent chassis in back. ER30DSR with no side panels no raised vent 3-inch side panels* and no raised vent no side panels and raised vent 3-inch side panels and raised vent H 23 1/2" (597 mm) 20 1/2" (521 mm) 24" (610 mm) 21" (533 mm) J 23 1/2" (597 mm) 20 1/2" to 23 1/2" 24" (610 mm) 21" to 24" K 24" to 25 9/16" 21" to 25 9/16" 24 1/2" to 26 1/16" 21 1/2" to 26 1/16" * Optional side panels (PN ARSP3) cover unfinished chassis sides when the cabinet face is recessed behind back of control panel. Installation Instructions Preparing for Installation WARNING • If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician. • Before installing the range, you must locate and secure the anti-tip bracket to the floor. • Be sure that the unit is not connected to gas or power before proceeding with the following sections. IMPORTANT: Within the Commonwealth of Massachusetts, this appliance must be installed by a licensed plumber or gas fitter. NOTE: When installing a backguard, always install it before sliding the range into place. See page 9. Unpacking the Range Unpack the range and verify that all required parts have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appliance. The customer must report cosmetic issues within 30 days of installation. 8 Parts List • 2 grates • 1 small stack burner cap • 1 small stack burner ring • 2 large stack burner caps • 2 large stack burner rings • 1 crown burner cap • 1 crown burner ring • 1 crown burner head • 1 GlideRack™ oven rack • 2 standard size racks • 4 knobs • Anti-tip bracket w/screws • Meat probe • Griddle • Wok ring • Stainless steel cleaner • Literature kit • Broiler pan/grill See the use and care manual for a list of optional accessories.