Dacor ER30DSR Installation Instructions - Page 22
Verifying Proper Operation, Installation Checklist - oven parts
View all Dacor ER30DSR manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Installation Instructions Verifying Proper Operation Before operating the range, read the accompanying use and care manual completely. 1. Before beginning the test procedure, ensure that all cooktop control valves are in the OFF position, and all burner rings, burner caps and grates are properly positioned on the cooktop frame. Turn on the gas supply at the shut-off valve. 2. Plug in the appliance cord, if applicable. Turn on power to the range at the circuit breaker or fuse box. 3. Set the time of day: Press the clock key. Enter the time on the number keypad (within 6 seconds). Press START. 4. Press the BAKE key. 5. Enter the temperature of 350°F on the keypad. 6. Press START. 7. The display should show BAKE, and the preheating temperature. 8. Press the CANCEL-SECURE key to stop the oven heating process. 9. Test one of the burners by pushing the knob in and turning it counterclockwise to the HIGH position. It may take up to four seconds for ignition to occur, at which time the ignitor will stop sparking. If ignition does not occur within four seconds, turn off the knob, wait for at least five minutes to allow any gas to dissipate, then repeat the ignition test. After ignition, rotate the control knob counterclockwise from HIGH to LOW to adjust the flame height progressively. When the range is installed properly, the flame will be steady and quiet. It will also have a sharp, blue inner cone that will vary in length proportional to the burner size. Dacor's Smart Flame™ feature reduces the flame under the grate fingers to increase grate life. If the Normal Flame range is equipped for use with LP gas, the ends of the flame may be yellow at the tips, which is normal. 10. Turn the control knob to the OFF position. 11. Repeat the ignition test for all remaining burners. OFF Icon If either the oven or cooktop does not operate properly, follow these troubleshooting steps: 1. Verify that power and gas are supplied to the range. 2. Check the electrical connections and gas supply to ensure that the installation has been completed correctly. 3. Repeat the above bake test or burner ignition test. 4. If the appliance still does not work, contact Dacor Distinctive Service at (877) 337-3226. Do not attempt to repair the appliance yourself. Have the model and serial numbers available when you call. See page 3 for location. Dacor is not responsible for the cost of correcting problems caused by a faulty installation. Installation Checklist WARNING • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. • Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor range cannot be overemphasized. □□ Has the plastic coating been peeled off of the outside of the range? Have all packaging materials been removed from inside the oven? □□ Are all leveling legs extended down to make contact with the floor? Is the unit level? See page 11. □□ Is the range secured in place with the provided anti-tip bracket and foot according to these instructions? See page 11. □□ If the wall in the back of the cooktop combustible, is a backguard or raised vent installed? □□ Is the range wired and grounded according to these instructions and in accordance with all applicable electrical codes? Has the electrical access cover been replaced? See Pages 4 and 12 to 17. □□ Has the gas supply inlet pressure been measured to ensure that it does not exceed the maximums stated in these instructions? See page 4. □□ Is the range connected to the gas supply according to these instructions and in accordance with all applicable codes? See page 17. □□ Did the installer check the gas supply for leaks? □□ Is the oven door properly installed according to these instructions? See page 18. □□ Have the burner knobs been installed in the proper positions? See page 18. □□ Are the burners and grates properly installed according to these instructions? See page 19. □□ Has proper operation been verified? □□ Has the warranty been activated on-line or the warranty card been filled out completely and mailed? 20