Dacor RNRP36G Installation Instructions - Page 15
Verifying Proper Operation, Removing the Range for Service, Reinstalling the Range After, Service,
![]() |
View all Dacor RNRP36G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Installation Instructions Verifying Proper Operation Before operating the range, read the accompanying use and care manual completely. It contains Important safety, service and warranty information. 1. Before beginning the test procedure, ensure that all cooktop control valves are in the OFF position, and all burner rings, burner caps, and grates are properly positioned on the cooktop frame. 2. Turn on the gas supply at the shut-off valve. 3. Connect the power cord to the electrical outlet. When the range is first connected, the oven indicator light flashes on and off for about 10 seconds while the range's circuitry starts up. Wait for the light to stop flashing before going to step 4. 4. Test one of the burners by pushing the knob in and turning it counterclockwise to the HIGH position. It may take up to four seconds for ignition to occur, at which time the ignitor will stop sparking. If ignition does not occur within four seconds, turn off the knob, wait for at least five minutes to allow any gas to dissipate, then repeat the ignition test. After ignition, rotate the control knob counterclockwise from HIGH to LOW to adjust the flame height progressively. When the range is installed properly, the flame will be steady and quiet. It will also have a sharp, blue inner cone that will vary in length proportional to the burner size. Dacor's Smart Flame™ feature reduces the flame under the grate fingers to increase grate life. If the range is equipped for use with LP gas, the ends of the flame may be yellow at the tips, which is normal. Normal Flame 5. Turn the control knob to the OFF position. 6. Repeat the ignition test for all remaining burners. After testing all the cooktop burners, turn them off. 7. Open the oven door(s). Test the oven light(s) by OFF Icon turning on the light switch(s) on the control panel. 8. Turn on the convection fan switch(s). You should hear the convection fan, located behind the screen at the back of the oven, come on. 9. With the oven door open, turn the oven control knob to the 400 degree position. Both the knob itself and the oven ON indicator light next to the knob should illuminate. Within 60 seconds you should hear the bake burner ignite below the oven floor. It should begin to give off heat. 10. Turn the oven control knob to the BROIL position. The bake burner should turn off. Both the oven control knob and the oven ON indicator light should be illuminated. 11. Within 60 seconds the IR burner on the ceiling of the oven should ignite and begin to give off heat. 12. Turn the oven knob to the "OFF" position. On model RNRP48G, test both ovens. If the range does not operate properly, follow these troubleshooting steps: 1. Verify that power and gas are supplied to the range. 2. Check the electrical connections and gas supply to ensure that the installation has been completed correctly. 3. Repeat the burner ignition test and/or oven test. 4. If the appliance still does not work, contact Dacor Distinctive Service at (800) 793-0093 ex. 2822. Do not attempt to repair the appliance yourself. Have the model and serial numbers available when you call. See inside cover for location. Dacor is not responsible for the cost of correcting problems caused by a faulty installation. Removing the Range for Service 1. Turn the gas supply valve to the off position. 2. Disconnect the power cord from the electrical outlet. 3. Pull the range out from the wall Reinstalling the Range After Service 1. Push the range into operating position, making sure the antitip bracket is engaged (see page 10). 2. Connect the power cord to the electrical outlet. 3. Turn the gas supply valve to the on position. Installation Checklist WARNING • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. • Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor range cannot be overemphasized. □□ Has the plastic coating been peeled off the outside of the range? Have all packaging materials been removed from inside the oven? □□ Are all leveling legs extended down to make contact with the floor? Is the unit level? See page 10. □□ Is the range secured in place with the provided anti-tip bracket and foot according to these instructions? See pages 6 and 10. □□ Has the gas supply inlet pressure been measured to ensure that it does not exceed the maximums stated in these instructions. See page 3. □□ Is the range connected to the gas supply according to these instructions and in accordance with all applicable codes? Did the installer check the gas supply for leaks? □□ Is the oven door properly installed according to these instructions? See page 10. □□ Have the burner knobs been installed in the proper locations? See page 11. □□ Are the burners assembled and grates properly installed according to these instructions? See page 12. □□ Has proper operation been verified? Has the warranty been activated on-line or the warranty card been filled out completely and mailed? 13
![](/manual_guide/products/dacor-rnrp48g-installation-instructions-456b090/15.png)