Dacor SGM304 Planning Guides
Dacor SGM304 Manual
 |
View all Dacor SGM304 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dacor SGM304 manual content summary:
- Dacor SGM304 | Planning Guides - Page 1
PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Drop-in Gas Cooktops Revised 01/27/11 Page 1/5 PLANNING GUIDE All tolerances ±1/16" (±1.6 mm), unless otherwise noted. warning • Observe all governing codes and ordinances during planning and installation. Contact your local building department - Dacor SGM304 | Planning Guides - Page 2
the cooktop being installed is correct for the gas service being provided (natural gas or LP gas). Also, if operating the cooktop at an altitude above 4000 ft. (1219 m) make sure it is equipped for high altitude operation. ◊ Units equipped for LP operation have "LP" in the model number listed on - Dacor SGM304 | Planning Guides - Page 3
a drawer installed below the cooktop. 1/4" (6 mm) min. clearance to combustible B surfaces Under Cabinet Clearances Model (B) Minimum* SGM304 29" (73.7 cm) SGM365 35 ¼" (89.5 cm) SGM466 46" (116.8 cm) * To allow clearance for hold down brackets ◊ The gas supply piping, gas shut-off - Dacor SGM304 | Planning Guides - Page 4
, SGM466 30", 36", 46" Wide, Gas Cooktops Revised 01/27/11 Page 4/5 PLANNING GUIDE Cutout Dimensions Cutout tolerances +1/16" (+1.6 mm), -0, unless otherwise noted IMPORTANT: Be careful to use the correct cutout diagram (on page 5/5) to determine the countertop dimensions for the installation - Dacor SGM304 | Planning Guides - Page 5
Document # PG04-004 SGM304, SGM365, SGM466 30", 36", 46" Wide, Gas Cooktops Cutout tolerances +1/16" (+1.6 mm), -0, unless otherwise noted Rear wall Revised 01/27/11 Page 5/5 PLANNING GUIDE Vertical combustible surface C D 4 1/4" (10.8 cm) min. from mounting surface to combustibles below
-
1 -
2 -
3 -
4 -
5
 |
 |
PLANNING
GUIDE
Specifications subject to change without notice.
Phone: (800) 793-0093
www.Dacor.com
SGM304, SGM365, SGM466
30”, 36”, 46” Wide,
Drop-in Gas Cooktops
30"
(76.2 cm)
1 5/8" (4.1 cm)
bottom of base
to cooking surface
27 5/8" *
(70.2 cm)
* including embosses/screws in side of chassis
19 1/2" *
(49.5 cm)
21"
(53.3 cm)
4" (10.2 cm)
chassis height
36"
(91.4 cm)
33 1/2" *
(85.1 cm)
* including embosses in side of chassis
19 1/2" *
(49.5 cm)
21"
(53.3 cm)
1 5/8" (4.1 cm)
bottom of base
to cooking surface
4" (10.2 cm)
chassis height
* including embosses/screws in side of chassis
46"
(116.8 cm)
44 5/8" *
(113.3 cm)
19 1/2" *
(49.5 cm)
21"
(53.3 cm)
1 5/8" (4.1 cm)
bottom of base
to cooking surface
4" (10.2 cm)
chassis height
All tolerances ±1/16” (±1.6 mm), unless otherwise noted.
PRODUCT DIMENSIONS -
MODEL SGM304
PRODUCT DIMENSIONS -
MODEL SGM365
PRODUCT DIMENSIONS -
MODEL SGM466
Document # PG04-004
Revised 01/27/11
Page 1/5
WARNING
•
Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
•
This appliance must be installed in accordance with the
accompanying installation instructions.