Danby DR3009WGLP Product Manual - Page 9
Care And Cleaning
View all Danby DR3009WGLP manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
CARE AND CLEANING • If removing the range is necessary for cleaning or CLEANING THE CONTOURED WELL AREAS, maintenance, shut off gas supply. BURNER CAPS, AND BURNER HEADS • Disconnect the gas and electrical supply. The contoured well areas, burner caps and burner • If the gas or electrical supply is inaccessible, lift the heads should be routinely cleaned. Keeping the burner unit slightly at the front and pull out away from the ports clean will prevent improper ignition and an wall. uneven flame. • Pull only as far as necessary to disconnect the gas To clean the recessed and contoured areas of the cook-top: and electrical supply. • If a spill occurs on or in the recessed or contoured • Finish removing the unit for servicing and cleaning. areas, blot up spill with an absorbent cloth. Rinse with • Reinstall in reverse order making sure to level the a clean, damp cloth and wipe dry. range and check gas connections for leaks. • See Anti-Tip Instructions for proper anchoring To remove and replace the surface burner caps and instructions. surface burner heads, remove in the following order: 1) Surface burner grates Control Panel and Knobs: 2) Surface burner caps, and • Before cleaning the control panel be sure that the 3) Surface burner heads knobs are in the OFF position. Clean with a soft cloth • Reverse the procedure above to replace the surface and warm soapy water. Remove residues and dry burner caps and surface burner heads. carefully; excess water in and around the controls •Use a soap-filled scouring pad or a mild abrasive may damage the stove. cleanser to clean the surface burner caps and surface • The control knobs may be removed for easier cleaning. burner heads. The ports or slots around the burner head To remove, pull them straight off the stem. Clean with must be routinely cleaned. If residue still remains in soft cloth and warm soapy water; rinse well. these ports, use a small-gauge wire or needle to clean • To replace knobs after cleaning, connect the flat side the slots or holes. of the knob cavity to the control rod and press against • For proper flow of gas and ignition of the burner do the knob to reconnect. not allow spills, food, cleaning agents or any other material to enter the gas orifice holder opening. Oven Rack: Always keep the surface burner cap and surface burner • To make the rack slide more easily you may apply a head in place whenever a surface burner is in use. small amount of vegetable oil or cooking oil to a paper towel and wipe the edges of the rack with it. THE COOK-TOP IS NOT REMOVABLE. DO NOT ATTEMPT TO REMOVE OR LIFT THE COOK-TOP. Broiler Pan: • Remove broiler pan from oven after broiling and Oven Surface: carefully pour out the grease from the pan into a • Be sure to wear rubber gloves to protect your hands. proper container. • Do not use oven cleaners, cleaning powders, steel • Wash and rinse the broiler pan using hot water and a wool pads, synthetic fiber pads, or any other soap-filled scouring pad. materials that may damage the surface finishing. • If food has burned on, sprinkle with detergent • If any acid, grease, sugar, etc. spills on surfaces while while it is hot and cover it with wet paper towels or a they are hot, use a dry paper towl or soft cloth to wipe it dishcloth. Soaking the pan will remove burned-on food. up right away. When the surface has cooled, clean with • Do not use commercial oven cleaners, cleaning soft cloth and warm soapy water; rinse well. powders, steel wool pads or harsh abrasives on any • You may also use a solution of vinegar and water to surfaces. Vinegar and water solution may be used. clean the oven surface. Use vinegar to remove hard stains (white stains). To Remove/Replace the Storage Drawer: • Heavy spattering or spillover may require cleaning • Pull the drawer all the way out until it stops. with a mildly abrasive cleaner.other material to enter • Lift the drawer by its handle and pull all of the way out. the gas orifice holder opening. Always keep the surface • To replace, reverse steps above. burner cap and surface burner head in place whenever a surface burner is in use. 8