Dell Alienware Aurora - R2 Service Manual (English only)
Dell Alienware Aurora - R2 Manual
View all Dell Alienware Aurora - R2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Alienware Aurora - R2 manual content summary:
- Dell Alienware Aurora - R2 | Service Manual (English only) - Page 1
ALIENWARE® AURORA SERVICE MANUAL 01 /01 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 2
any manner whatsoever without the prior written permission of Dell Inc. is strictly prohibited. Trademarks used in this manual: Alienware is a registered trademark of Alienware Corporation; Dell and the DELL logo are trademarks of Dell Inc.; Bluetooth is a registered trademark owned by Bluetooth SIG - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 3
Panel 11 CHAPTER 3: TECHNICAL OVERVIEW 12 Inside View of Your Computer 13 System Board Components 14 Master I/O Board Components 15 CHAPTER 4: Card Reader 27 Replacing the Media Card Reader 29 CHAPTER 6: PCI-EXPRESS CARD(S 30 Removing the PCI-Express Card(s 32 Replacing the PCI-Express Card - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 4
Liquid-Cooling Assembly 48 Replacing the Processor Liquid-Cooling Assembly 49 CHAPTER 10: PROCESSOR 50 Removing the Processor 52 Replacing the Processor 53 CHAPTER 11: POWER SUPPLY 55 Removing the Power Supply 57 Replacing the Power Supply 59 CHAPTER 12: BATTERY 60 Removing the Coin - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 5
Replacing the Bluetooth Assembly 101 CHAPTER 21: TOP I/O PANEL 102 Removing the Top I/O Panel 104 Replacing the Top I/O Panel 105 CHAPTER 22: SYSTEM SETUP 106 Configuring the BIOS 107 Clearing Forgotten Passwords and CMOS Settings 114 APPENDIX A: CONTACTING ALIENWARE 117 CONTENTS 05 /05 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 6
CHAPTER 1: BEFORE YOU BEGIN CHAPTER 1: BEFORE YOU BEGIN CHAPTER 1: BEFORE YOU BEGIN This manual provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: • You have performed the steps in " - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 7
in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • BIOS executable update program available at support.dell.com CHAPTER 1: BEFORE YOU BEGIN Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 8
outlets. 5. Disconnect all attached devices from your computer. 6. Press and eject any installed cards from the Media Card Reader. 7. Press and hold the power button to ground the system board. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 9
CHAPTER 2: SIDE PANEL CHAPTER 2: LEFT SIDE-PANEL CHAPTER 2: LEFT SIDE-PANEL 09 /09 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 10
: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 11
(available only in Alienware Aurora ALX) turns on automatically when the left side-panel is removed. Replacing the Left Side-Panel 1. Follow the instructions in "Before You Begin" on page 6. 2. Align the tabs on the left side-panel with the slots on the side of the computer and push the panel - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 12
CHAPTER 3: TECHNICAL OVERVIEW CHAPTER 3: TECHNICAL OVERVIEW CHAPTER 3: TECHNICAL OVERVIEW 012 /012 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 13
that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 3 2 1 CHAPTER 3: TECHNICAL OVERVIEW 4 1 memory module(s) 3 optical drives (3) 2 graphic cards (2) 4 hard drives (4) 013 /013 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 14
18 17 16 15 CHAPTER 3: TECHNICAL OVERVIEW 1 processor power connector (PWR2) 2 processor socket (CPU) 3 processor fan connector (MB_CPU_FAN) 4 memory-module connector (DIMM2) (Aurora and Aurora ALX ) memory-module connector (DIMM3) (Aurora-R2) 5 memory-module connector (DIMM1) 6 memory-module - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 15
(PWR_SEL) 10 Bluetooth® connector (BLUETOOTH) 14 11 power-LED board connector (BLINK) 12 wireless connector (WIRELESS) 15 13 hard-drive LED connector (HDD_LED1) 14 hard-drive LED connector (HDD_LED2) 15 USB connector (MB_USB) 16 main-power connector (PWR1) 16 17 system-board lighting - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 16
CHAPTER 5: SHROUDS CHAPTER 4: SHROUDS CHAPTER 4: SHROUDS 016 /016 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 17
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 18
the instructions in "Before You Begin" on page 6. 2. Lower the PCI shroud into the chassis until it clicks into place. 3. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 4. Connect your computer and devices to electrical outlets and then turn them on. 1 release button - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 19
on the master I/O board. Replacing the Drive-Bay Shroud 1. Follow the instructions in "Before You Begin" on page 6. 2. Connect the drive-bay shroud Replacing the Left Side-Panel" on page 11). 7. Connect your computer and devices to electrical outlets and then turn them on. 1 1 tabs (2) CHAPTER 4: - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 20
CHAPTER 6: DRIVE(S) CHAPTER 5: DRIVE(S) CHAPTER 5: DRIVE(S) 020 /020 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 21
the back of the computer). NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell or Alienware. NOTE: If you are installing a hard drive from a source other than Dell or Alienware, you need to install an operating system, drivers, and utilities on - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 22
(s) CAUTION: If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Disconnect the - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 23
the hard-drive assembly out of the harddrive cage. CHAPTER 5: DRIVE(S) 5. Remove the hard drive out of the hard-drive bracket by releasing the tabs and lifting the hard drive out of the bracket (if applicable). 1 2 1 2 1 hard-drive assembly 2 release tabs (2) 1 hard drive 2 tabs (4) 023 /023 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 24
the instructions in the hard-drive cage until the release tabs snap into place. 5. Connect the power and data cables to the hard -drive assembly (if applicable). 6. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 7. Connect your computer - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 25
instructions in "Before You Begin" on page 6. 2. Press the AlienHead on the front of your computer to lower the drive panel. 3. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 4. Open the PCI shroud (see "Opening the PCI Shroud" on page 18). 5. Disconnect the power - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 26
Replacing the Optical Drive(s) 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove securing tab and slide the optical drive through the front of the computer until the securing tab snaps into place. 5. Connect the power and data cables to the optical drive (if applicable). 6. Close - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 27
Removing the Media Card Reader 2 1. Follow the instructions in "Before You Begin" on page 6. 2. Press the AlienHead on the front of your computer to lower the drive panel. 3. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 1 4. Open the PCI shroud (see "Opening - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 28
7. Remove the four screws that secure the Media Card Reader to the FlexBay dock. 8. Slide the Media Card Reader out of the FlexBay dock. 1 CHAPTER 5: DRIVE(S) 2 3 1 Media Card Reader 3 screws (4) 2 FlexBay dock 028 /028 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 29
dock. 4. Replace the four screws that secure the Media Card Reader to the FlexBay dock. 5. Lift the securing tab and slide the FlexBay dock through the front of the computer until the securing tab snaps into place. 6. Connect the FlexBay USB cable to the connector on the master I/O board. 7. Close - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 30
CHAPTER 6: PCI EXPRESS CARD(S) CHAPTER 6: PCI-EXPRESS CARD(S) CHAPTER 6: PCI-EXPRESS CARD(S) 030 /030 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 31
unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER 6: PCI-EXPRESS CARD(S) 031 /031 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 32
PCI-Express Card(s) 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see "Opening the PCI Shroud" on page 18). 4. Locate the PCI-Express card on the system board (see "System Board - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 33
Replacing the PCI-Express Card(s) 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the filler bracket to create a card-slot opening (if applicable). 1 CHAPTER 6: PCI-EXPRESS CARD(S) 2 1 filler bracket 2 screw 033 /033 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 34
securing clips are in the closed position. 3. Align the card with the card connector on the system board. 4. Place the card in the connector and press down firmly. Ensure that the card is firmly seated in the slot. If you are installing the PCI-Express x16 card, push the securing tab and insert the - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 35
modules on the system board. See the specifications in your Desktop Manual at support.dell.com/manuals for information on the type of memory supported by your computer. Install only memory modules that are supported by your computer. NOTE: Memory modules purchased from Dell or Alienware are covered - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 36
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 37
(s) to cool before touching them. NOTE: For better access to the memory module(s), remove the graphics card if the card is full length. 4. To remove the graphics card, see "Removing the PCI-Express Card(s)" on page 32. 5. Spread apart the securing clips at both ends of the memory-module connector - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 38
Replacing the Memory Module(s) 1. Follow the instructions in "Before You Begin" on page 6. Recommended memory configuration: Aurora/Aurora ALX Aurora-R2 CHAPTER 7: MEMORY MODULE(S) Type 1066 MHz and I333 MHz DDR3 1600 MHz XMP Slots Slots 1, 3, and 5 or slots 1 - 6 Slots 1, 3, and 5 Type 1066 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 39
-Express Card(s)" on page 33. 5. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 6. Connect your computer and devices to electrical outlets and then turn them on. As the computer boots, it detects the additional memory and automatically updates the system configuration - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 40
CHAPTER 8: FANS CHAPTER 8: FANS CHAPTER 8: FANS 040 /040 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 41
: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 42
Removing the Hard-Drive Fan Assembly 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see " - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 43
Replacing the Hard-Drive Fan Assembly 1. Follow the instructions in "Before You Begin" on page 6. 2. Push the hard-drive fan side-panel (see "Replacing the Left Side-Panel" on page 11). 8. Connect your computer and devices to electrical outlets and then turn them on. CHAPTER 8: FANS 043 /043 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 44
Removing the PCI-Fan Assembly 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the the Drive-Bay Shroud" on page 19). 5. Remove full-length PCI-Express cards, if any (see "Removing the PCI-Express Card(s)" on page 32). 6. Disconnect the PCI-fan assembly cable from the connector - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 45
Follow the instructions in "Before You Begin" on page 6. 2. Align the PCI-fan assembly with the metal bracket on the chassis. 3. Slide the PCI-fan assembly into the chassis. 4. Connect the PCI-fan assembly cable to the connector on the master I/O board. 5. Replace full-length PCI-Express cards, if - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 46
CHAPTER 9: LIQUID COOLING ASSEMBLY CHAPTER 9: PROCESSOR LIQUID-COOLING ASSEMBLY CHAPTER 9: PROCESSOR LIQUID-COOLING ASSEMBLY 046 /046 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 47
to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). CHAPTER 9: PROCESSOR - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 48
-cooling assembly cable from the connectors (SYS FAN and CPU PUMP) on the top-lighting board. 4. Loosen the four captive screws that secure the processor liquid-cooling assembly to the system board. 5. Remove the four screws that secure the processor liquid-cooling assembly to the chassis rear wall - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 49
liquid-cooling assembly to the system board. 5. Connect the processor liquid-cooling assembly cables to the connectors (SYS FAN and CPU PUMP) on the top lighting-board. 6. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 7. Connect your computer and devices to electrical - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 50
CHAPTER 9: PROCESSOR CHAPTER 10: PROCESSOR CHAPTER 10: PROCESSOR 050 /050 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 51
to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). CHAPTER 10: PROCESSOR - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 52
. 5. Open the processor cover and gently lift the processor to remove it from the socket. 6. Leave the release lever extended in the release position so that the socket is ready for the new processor. 1 processor cover 3 socket 5 tab CHAPTER 10: PROCESSOR 1 2 3 4 2 processor 4 release lever 052 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 53
-1 corners of the processor and socket. 5. Set the processor lightly in the socket and ensure that the processor is positioned correctly. 1 1 tab 3 processor 5 center-cover latch 7 processor pin-1 indicator CHAPTER 10: PROCESSOR 2 3 4 5 7 6 2 processor cover 4 socket 6 release lever 053 /053 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 54
seated in the socket, close the processor cover. Ensure that the tab on the processor cover is positioned underneath the center-cover latch on the socket. 7. Pivot the socket release lever back towards the socket, and snap it into place to secure the processor. 8. Clean the thermal grease from the - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 55
CHAPTER 10: POWER SUPPLY CHAPTER 11: POWER SUPPLY CHAPTER 11: POWER SUPPLY 055 /055 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 56
(including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER 11: POWER SUPPLY 056 /056 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 57
Removing the Power Supply 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Lift the tab and slide the power-supply cover towards the back of the chassis. 4. Lift the power-supply cover away from the chassis. - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 58
screws that secure the power supply to the back of the chassis. 7. Slide the power supply through the back of the chassis. CHAPTER 11: POWER SUPPLY 8. Remove the four screws that secure the power supply to the bezel. 9. Remove the bezel from the power supply. 1 1 power supply 1 2 2 captive screws - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 59
Replacing the Power Supply 1. Follow the instructions in "Before You Begin" on page 6. 2. Replace the four screws that secure the power supply to the bezel. 3. Slide the power supply into the chassis through the back of the computer. 4. Tighten the four captive screws that secure the power supply to - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 60
CHAPTER 14: COIN CELL BATTERY CHAPTER 12: BATTERY CHAPTER 12: BATTERY 060 /060 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 61
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 62
system setup (see "System Setup" on page 107) so that you can restore the correct settings after the new battery has been installed. 2. Follow the instructions any PCI-Express cards (see "Removing the PCI-Express Card(s)" on page 32). 6. Locate the battery socket (see "System Board Components" on - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 63
CHAPTER 12: BATTERY 6. Connect your computer and devices to electrical outlets and then turn them on. 7. Enter system setup (see "Entering System Setup" on page 107) and restore the settings you recorded before removing the battery. 3. Replace the PCI-Express cards (see "Replacing the PCI-Express - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 64
Removing the Theater-Lighting Batteries 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see " - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 65
Replacing the Theater-Lighting Batteries 1. Follow the instructions in "Before You Begin" on page 6. 2. Insert the two new batteries panel (see "Replacing the Left Side-Panel" on page 11). 7. Connect your computer and devices to electrical outlets, and then turn them on. CHAPTER 12: BATTERY 065 /065 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 66
CHAPTER 11: SYSTEM BOARD CHAPTER 13: SYSTEM BOARD CHAPTER 13: SYSTEM BOARD 066 /066 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 67
always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER 13: SYSTEM BOARD 067 /067 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 68
18). 5. Remove any PCI-Express cards (see "Removing the PCI-Express Card(s)" on page 32). WARNING: Despite having a plastic shield, the processor liquid-cooling assembly may be very a disconnected cable could lead to computer problems. 1 1 latch CHAPTER 13: SYSTEM BOARD 2 2 screws (2) 068 /068 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 69
liquid-cooling assembly (see "Replacing the Processor Liquid-Cooling Assembly" on page 49). 8. Replace the PCI-Express cards (see "Replacing the PCI-Express Card(s)" on page 33). 9. Close the PCI shroud (see "Closing the PCI Shroud" on page 18). 10. Replace the left side-panel (see "Replacing - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 70
CHAPTER 12: MASTER I/O BOARD CHAPTER 14: MASTER I/O BOARD CHAPTER 14: MASTER I/O BOARD 070 /070 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 71
side panels, bezels, filler brackets, front-panel inserts, etc.) removed. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 72
Removing the Master I/O Board 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see " - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 73
Replacing the Master I/O Board 1. Follow the instructions in "Before You Begin" on page 6. 2. Place the master I/O board in the (see "Replacing the Left Side-Panel" on page 11). 9. Connect your computer and devices to electrical outlets, and then turn them on. CHAPTER 14: MASTER I/O BOARD 073 /073 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 74
CHAPTER 13: TOP LIGHTING BOARD CHAPTER 15: TOP LIGHTING-BOARD CHAPTER 15: TOP LIGHTING-BOARD 074 /074 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 75
panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 76
board away from the chassis. Replacing the Top Lighting-Board 1. Follow the instructions in "Before You Begin" on page 6. 2. Replace the four screws (see "Replacing the Left Side-Panel" on page 11). 5. Connect your computer and devices to electrical outlets and then turn them on. 1 top lighting-board - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 77
CHAPTER 16: RIGHT SIDE PANEL CHAPTER 16: RIGHT SIDE-PANEL(S) CHAPTER 16: RIGHT SIDE-PANEL(S) 077 /077 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 78
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 79
instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see "Opening the PCI Shroud" on page 18). 4. Remove the drive-bay shroud (see "Removing the Drive-Bay Shroud" on page 19). 5. Remove the power-supply - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 80
8. Place the chassis in an upright position. 9. Slide and pull the right top-panel away from the chassis. CHAPTER 16: RIGHT SIDE-PANEL(S) 10. Disconnect the lighting-board cable from the connector on the master I/O board. 11. Remove the two screws that secure the lighting board to the chassis. - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 81
1. Follow the instructions in "Before You Begin" on page 6. 2. Align the right bottom-panel to the bottom of the computer and slide it see "Replacing the Power Supply" on 1 page 59). 9. Replace the hard-drive fan assembly (see "Replacing the Hard-Drive Fan Assembly" on page 43). 10. Replace the - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 82
CHAPTER 17: ACTIVE VENTING ASSEMBLY CHAPTER 17: ACTIVE-VENTING ASSEMBLY CHAPTER 17: ACTIVE-VENTING ASSEMBLY 082 /082 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 83
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 84
Removing the Active-Venting Assembly NOTE: Active-venting assembly is available only in Alienware Aurora ALX. 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see " - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 85
the active-venting assembly to the chassis. CHAPTER 17: ACTIVE-VENTING ASSEMBLY 8. Place the chassis in an upright position. 9. Remove the right top-panel. 1 1 1 screws (10) 1 right top-panel 085 /085 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 86
10. Remove the two screws that secure the top panel to the chassis. 11. Lift the top panel away from the chassis. 1 12. Remove the three - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 87
Assembly 1. Follow the instructions in "Before You Begin Replacing the Top Lighting-Board" on page 76). CHAPTER 17: ACTIVE-VENTING ASSEMBLY 10. Replace the screw that secures the right top-panel to the chassis. 11. your computer and devices to electrical outlets and then turn them on. 087 /087 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 88
CHAPTER 18: FRONT BEZEL CHAPTER 18: FRONT BEZEL CHAPTER 18: FRONT BEZEL 088 /088 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 89
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 90
Removing the Front Bezel 1 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the PCI shroud (see " - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 91
8. Place the chassis in an upright position. 9. Remove the three screws on the right side that secure the front bezel to the chassis. 10. Pull the front bezel away from the chassis. 1 CHAPTER 18: FRONT BEZEL 2 1 front bezel 2 screws (3) 091 /091 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 92
Replacing the Front Bezel 1. Follow the instructions in "Before You Begin" on page 6. 2. Align see "Closing the PCI Shroud" on page 18). 10. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 11. Connect your computer and devices to electrical outlets and then turn them on - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 93
CHAPTER 16: BACK PANEL CHAPTER 19: BACK BEZEL CHAPTER 19: BACK BEZEL 093 /093 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 94
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 95
Bezel 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Remove the power supply (see "Removing the Power Supply" on page 57). WARNING: Despite having a plastic shield, the processor liquid-cooling assembly - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 96
7. Remove the two screws that secure the back bezel to the chassis. 8. Release the tabs that secure the back bezel to the chassis. 9. Pull the back bezel away from the chassis. CHAPTER 19: BACK BEZEL 1 2 1 screws (2) 3 tabs 3 2 back bezel 096 /096 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 97
the Back Bezel 1. Follow the instructions in "Before You Begin" on Processor Liquid-Cooling Assembly" on page 49). 7. Replace the power supply (see "Replacing the Power Supply" on page 59). 8. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 9. Connect your computer - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 98
CHAPTER 18: FRONT BEZEL CHAPTER 20: BLUETOOTH ASSEMBLY CHAPTER 20: BLUETOOTH ASSEMBLY 098 /098 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 99
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 100
Removing the Bluetooth Assembly NOTE: The Bluetooth® assembly is available on your computer only if you ordered it while purchasing your computer. 1. Follow the instructions in "Before You Begin" on page 6. 2. Remove the left side-panel (see "Removing the Left Side-Panel" on page 11). 3. Open the - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 101
Replacing the Bluetooth Assembly 1. Follow the instructions in "Before You Begin" on page 6. 2. Align the tabs on the -panel (see "Replacing the Left Side-Panel" on page 11). 8. Connect your computer and devices to electrical outlets and then turn them on. CHAPTER 20: BLUETOOTH ASSEMBLY 0101 /0101 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 102
CHAPTER 20: TOP I/O CHAPTER 21: TOP I/O PANEL CHAPTER 21: TOP I/O PANEL 0102 /0102 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 103
against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CHAPTER - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 104
instructions 6. Remove any PCI-Express cards (see "Removing the PCI-Express Card(s)" on page 32). 7. 10. Pull the panel insert away from the chassis. 11. Remove the four screws that secure the top I/O panel to the chassis. 12. Disconnect the top I/O panel cables from the connectors on the system - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 105
instructions in "Before You Begin" on page 6. 2. Align and replace the top I/O panel. 3. Connect the top I/O panel cables to the connectors on the system 9. Replace the PCI-Express cards (see "Replacing the PCI-Express Card(s)" on page 33). CHAPTER 21: TOP I/O PANEL 10. Replace the PCI-fan assembly - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 106
CHAPTER 21: SYSTEM SETUP CHAPTER 22: SYSTEM SETUP CHAPTER 22: SYSTEM SETUP 0106 /0106 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 107
during POST (Power On Self Test), press when the prompt appears to enter the BIOS Setup Utility. NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop, then shut down your desktop and try again. System Setup Screens The - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 108
. System Information Product Name BIOS Version Service Tag Asset Tag Memory Installed Memory Available Memory Technology Memory Speed CPU ID/u Code ID CPU Speed Displays the product name. Displays the BIOS version number and date information. Displays the service tag of the computer. Displays - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 109
updated according to the hard drives detected. Sets the CD/DVD drive boot priority. CHAPTER 22: SYSTEM SETUP CPU Configuration XD Bit Capability Intel® Speedstep™ tech Intel® C State Tech Intel® HT Technology (available on Aurora-R2 only) Enable XD Bit Capability to allow the processor - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 110
Remote Wakeup (available on Aurora and Aurora ALX only) Auto Power On Sets the energy-saving mode of the ACPI function. Sets what action the computer takes when power is restored. Sets the system to wake up from an onboard LAN, PCIE-X1 LAN card, or a PCI LAN card. Allows the computer to start up at - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 111
DMI Speed (available on Aurora-R2 only) QPI Frequency (available on Aurora and Aurora ALX only) DMI Frequency (available on Aurora-R2 only) Memory Ratio Core (Non-Turbo) Ratio Advance DRAM Configuration Overclock Configuration Displays the current processor speed. Displays the current memory - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 112
Displays the Command Rate (editable in Manual Mode). CHAPTER 22: SYSTEM SETUP Overclock Configuration Submenu Adjust CPU BClk (MHz) Allows you to adjust BClk of processor. Spread Spectrum Enable/disable spread spectrum modulation. Adjust PCI Frequency (MHz) (available on Aurora and Aurora ALX - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 113
(available on Aurora-R2 only) Displays the processor temperature in Celsius and Fahrenheit. Displays processor core voltage. Processor core voltage offset. Adjust the DDR3 memory voltage. Adjust the IOH voltage. Adjust QPI and uncore voltage. Adjust DMI and uncore voltage. BIOS Security Features - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 114
Settings CMOS: 1. Follow the instructions in "Before You Begin" on page 6. WARNING: The computer must be disconnected from the CMOS settings: a. Locate the 3-pin CMOS or password-reset jumper on the system board (see "System Board Components" on page 14). b. Remove the jumper plug from the - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 115
PASSWORD: 4. Replace the left side-panel (see "Replacing the Left Side-Panel" on page 11). 5. Connect your computer and devices to electrical outlets and then turn them on. CHAPTER 22: SYSTEM SETUP 0115 /0115 - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 116
the system board. To flash the BIOS: 1. Turn on the computer. 2. Go to support.dell.com/support/downloads. 3. Locate the BIOS update file for your computer: - If you have your computer's Service Tag: a. Click Enter a Service Tag. b. Enter your computer's Service Tag in the Enter a service tag: field - Dell Alienware Aurora - R2 | Service Manual (English only) - Page 117
the method of contacting Dell that is convenient for you. NOTE: For telephone support in the United States, call 1-800-Alienware. APPENDIX A: CONTACTING ALIENWARE Websites You can learn about Alienware® products and services on the following websites: • www.dell.com • www.dell.com/ap (Asian/Pacific
01
01
/
A
L
IENWARE
®
AURORA
SERVICE MANUAL