Dell Dimension E520 Owner's Manual - Page 95

Gently slide the drive into place until you feel a click or feel the drive securely installed.

Get Dell Dimension E520 PDF manuals and user guides View all Dell Dimension E520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

1 2 1 drive 2 screws (4) 1 Follow the procedures in "Before You Begin" on page 59. 2 Remove the drive panel (see "Removing the Drive Panel" on page 83). 3 Gently slide the drive into place until you feel a click or feel the drive securely installed. NOTE: If you are installing a new floppy drive rather than replacing a drive, remove the drive panel insert where you want the drive to be installed, insert the shoulder screws located in the back of the drive panel insert into the drive, and then slide the drive back into place. 4 Attach the power and data cables to the floppy drive. 5 Connect the other end of the data cable to the connector labeled "DSKT2" on the system board (see "System Board Components" on page 68) and route the cable through the clip on the shroud. Removing and Installing Parts 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Removing and Installing Parts
95
1
Follow the procedures in "Before You Begin" on page59.
2
Remove the drive panel (see "Removing the Drive Panel" on page 83).
3
Gently slide the drive into place until you feel a click or feel the drive securely installed.
NOTE:
If you are installing a new floppy drive rather than replacing a drive, remove the drive panel insert where
you want the drive to be installed, insert the shoulder screws located in the back of the drive panel insert into the
drive, and then slide the drive back into place.
4
Attach the power and data cables to the floppy drive.
5
Connect the other end of the data cable to the connector labeled "DSKT2" on the system board (see
"System Board Components" on page 68) and route the cable through the clip on the shroud.
1
drive
2
screws (4)
1
2